Page 61 / 165 Scroll up to view Page 56 - 60
Telsey telecommunications
Web Interface
53
MT500--SIEN12
Select a WAN interface from the drop-down menu (
Interface name
).
SIP Proxy Server’s IP Address and port can be typed in after selecting
Use
SIP Proxy
checkbox. It is also possible to use an alternate SIP Proxy Server
is case the main one is down or unreachable.
If a SIP Registrar is required in the network, then it is possible to set its IP
Address, port and SIP Time to Live after selecting
Use SIP Registrar
checkbox. It is also possible to use an alternate SIP Registrar in case the
first one is down or unreachable.
TimeOut
parameter determines when the
CPE sends the request to Alternative Proxy. When the TimeOut is expired
the CPE will try to go back to Proxy (Registrar).
Note
: The number of requests (
Retries
) to send to Proxy (or Registrar), before
the CPE switches to Alternative Proxy (Alternative Registrar) MUST be specified
(1 request by default).
If a SIP log messages server is required in the network, then it is possible
to set its IP address and port, after selecting
Remote Server for SIP log
messages
checkbox.
The SIP protocol can be configured to use the UDP/TCP or BOTH protocol as
Transport protocol type
.
SDP Export Type
. When the application is initiating a session, it can choose
to be the offerer or the answered. If it acts as the
offerer
, the application
must include an
SDP packet in the
INVITE
. The remote UA must then
include the answer SDP packet into its 200 OK response. If the application
wants to act as the
answerer
, then it must not include any SDP packet into
the INVITE: it will be up to the remote UA the inclusion of an offer in its 200
OK response. After receiving an offer into a 200 OK response, the
application must include its answer into the following
ACK
request.
It is possible to enable
OutOfBand DTMF
and assign a suitable payload of
the RTP packets, according to RFC2833. Valid payload range is from 96 to
127.
Supplementary Services
CLIR:
To set the caller ID restriction, dial *31# (default) then the
number.
CLIR permanent: enable *32# (default).
CLIR permanent: disable
#32# (default).
Call Hold:
To put a call on hold, press flash than hang up (optional).
To return to the original call, press flash or pick up the phone.
The phone will issue a short ring burst every 20 seconds or so
while on-hook to remind you
that a call is on hold.
Call transfer:
To transfer a call, press flash then dial the new number.
To transfer immediately, hang up (blind transfer)
To transfer with consultation, wait for the party to answer, consult,
and then hang up.
Page 62 / 165
Telsey
telecommunications
Web Interface
MT500--SIEN12
54
To abort the transfer (if the third party does not answer), press
flash to return to the original call.
Conference calling:
To turn a two-party call into a three-party conference call, press
flash and dial the third party.
To place the old (current) call on hold and take the new call press
flash+2 (R2).
To switch between the old and the new call press flash+2 (R2).
To connect to both the old and the new call press flash+3 (R3).
Starts a 3-party conference call.
To return in the state before the conference, press flash+2 (R2).
To drop yourself out of the conference, hang up. The call will be
transferred (so that the other two parties remain connected to
each other).
Note
: In conference mode, the conference initiator performs the audio
bridge/mixing function. There are only 2 voice streams established.
Call Waiting:
If call waiting is enabled on a line, you will hear the call waiting
tone during a call.
To press flash+2 to answer the second call. The first call is
automatically placed on hold.
To switch between calls, press flash+2 (R2).
To connect both the old and the new call flash+3 (R3). Starts a 3-
party conference call.
To reject the new call without answering it, press flash+0 (R0).
To release the old call and take the new call, press flash+1 (R1).
To enable the call waiting feature, dial *43# (default).
To disable the call waiting feature, dial #43# (default).
Call forward feature settings (Busy or All) takes priority over the
call waiting feature.
Call waiting feature is ignored on new incoming calls if there is
already a call on hold or in conference.
Call forward:
To set the call forward on no answer, dial *61* (default), then the
number and the termination character "#". Incoming calls will be
forward if unanswered for 18 seconds (default).
To set the call forward if busy, dial *67* (default), then the
number and the termination character "#". Incoming calls will be
immediately forwarded if the phone id off-hook.
To set the call forward unconditional, dial *21* (default), then the
number and the termination character "#".
To disable all the forward, dial #21# (default).
Call return:
Page 63 / 165
Telsey telecommunications
Web Interface
55
MT500--SIEN12
To place a call to the last know incoming caller (unanswered or
not), dial *69# (default).
Redial:
To redial the last outgoing number, dial *68# (default).
SS Configuration
Use the CLI (command
suppServs
) or Web page to set the special codes.
See the following table for code configuration:
The suppServer command string has the following structure:
CodeCommand, CodeCommand
E x a m p l e
WO*43#,WF#43#,FU*21*
Enable Call Waiting --> *43#
Disable Call Waiting --> #43#
Enable Call Forwarding Unconditional --> *21*
SS Enable/Disable services
Use the CLI or Web page to enable or disable the service. The following table
provide information on the services and call features parameters. The services
parameter is in bitmap format. The default is 0xffff.
Tab. 13: Supplementary services codes
Supplementary service
Code
Call Waiting ON
WO
Call Waiting OFF
WF
Call forwarding
Unconditional (All)
FU
Call forwarding if Busy
FB
Call forwarding on No
answer
FA
Call forwarding OFF
FF
Call Return
CR
Call Redial
CD
CLIR for call
RT
CLIR permanent ON
RO
CLIR permanent OFF
RF
Tab. 14: SS bitmap codes
Bit
Mask
Explanation
Bit 0
0x1
Call Waiting
Bit 1
0x2
Call Forwarding
Bit 2
0x4
Call Transfer
Page 64 / 165
Telsey
telecommunications
Web Interface
MT500--SIEN12
56
It is possible to set a
Digest Authentication,
by choosing an username and
password for each telephone line, if the SIP Registrar supports this feature.
Type the phone numbers for Line 1 and Line 2 and select an appropriate Dial
Plan (see Appendix A for more details).
Click on
Change SIP Parameters
and reboot to apply new settings.
By clicking on
Common
(Voice sub-menu), the following page shows up.
For each available Codec (G711μ-law, G711A-law, G729), it is possible to
choose:
Packetization time
Echo Canceller
Silence Suppression
Codec Priority order:
select the preferred order for the available codecs.
Bit 3
0x8
Call Hold
Bit 4
0x10
3-Way Conference
Bit 5
0x20
Call Return
Bit 6
0x40
Call Redial
Bit 7
0x80
CLIR
Tab. 14: SS bitmap codes
Bit
Mask
Explanation
Page 65 / 165
Telsey telecommunications
Web Interface
57
MT500--SIEN12
Country tone
(North America, Italy, UK, France, Sweden, Netherlands,
Belgium and Germany)
1
Caller ID Signal Type
(FSK, DTMF)
It is possible to activate
Squelch for InBand DTMF.
Fax passthrough codec
: select the preferred codec among G711A-law,
G711μ-law. Echo canceller will be disabled when fax/modem tone has been
detected.
HookFlash interval
: type the time range, in milliseconds, for the HookFlash.
Click on
Change Common parameters
to apply the new settings.
1.
See Appendix A for more specifications regarding Country tones.

Rate

4 / 5 based on 1 vote.

Popular Telsey Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top