Page 116 / 120
Scroll up to view Page 111 - 115
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
116
116
Monitoring | Iperf
Monitor > Iperf
Iperf is a tool to measure network environment such as throughput, packet loss and delay jitter.
Typically, to use Iperf, there should be a client and a server. The server opens a port and waits for
clients to build the connection. Iperf in CPE only plays as a client.
Status:
Enable/Disable Iperf.
Last Measurement Date/Time:
As titled.
Server Address:
As titled.
Server Port:
As titled.
Management Port:
To do bi-directional transmission, CPE opens
“
management port
”
to let
the server transmit data to itself.
Management Time:
The time to do Iperf recording.
Protocol Type: TCP
or
UDP
.
TCP Client Number (protocol type: TCP):
The
number of simultaneous TCP connection to
Page 117 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
117
117
the server.
Data Length (protocol type: UDP):
The size of datagram.
UDP Bandwidth (protocol type: UDP):
The UDP bandwidth to send in bits/sec.
Monitor Period Configuration:
The result
Uplink Latency (only UDP)
Downlink Latency (only UDP)
Uplink Speed.
Downlink Speed.
Page 118 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
118
118
Monitoring| Diagnostic Tools
Monitor > Diagnostic Tools
CPE has built-in tools
“
ping
”
and
“
traceroute
”
.
“
ping
”
is used to test if CPE can reach an IP
address or domain by sending the ICMP
“
ECHO_REQUEST
”
packet and waiting for the ICMP
“
ECHO_RESPONSE
”
packet.
“
traceroute
”
records all the relay points from CPE to an IP address or
domain. The result of
“
ping
”
and
“
traceroute
”
will be presented in
“
Diagnostic Result
”
.
Both ping and traceroute are using management interface only (not on data path).
Status:
Enable/Disable the tool.
Diagnostic Type:
ping or traceroute.
IP Address/Domain:
The IP address or domain name for CPE to connect.
Ping Count (Diagnostic Type: ping):
Stop after sending
“
Ping Count
”
packets.
Packet Size(Diagnostic Type:ping):
As titled.
Ping Timeout(Diagnostic Type:ping):
Time to wait for the response packet back to CPE.
Max Hops(Diagnostic Type: traceroute)
: The number of relay point that a packet can pass
by.
Diagnostic Result
: The result of
“
ping
”
or
“
traceroute
”
will be shown here.
Page 119 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
119
119
About
About| Status
About > Status
This section shows CPE basic information.
Service Provider:
As titled.
Product Name:
The name is composed of functions provided by CPE.
Model ID:
The ID used by the manufacturer.
Hardware Version:
As titled.
Serial ID:
The ID used by the operator.
IMEI:
International mobile equipment identity.
IMSI:
international mobile subscriber identity.
Firmware Version:
The version of the firmware.
Firmware Creation Date:
As titled.
Page 120 / 120
LTE/WiMAX DM Outdoor | User Manual
Dual Mode CPE7000 Manual
120
120
Bootrom Version:
The version of the boot loader.
Bootrom Creation Date:
As titled.
WiMAX Frequency Range:
The supported WiMAX frequency range.
LTE Support Band:
The supported LTE band.
19216811.live