13

1 GETTING STARTED

DMS-CTC-20110713-0016 v2.0

Manually activating the status LEDs

If the ECO(

) button is green or blue, you first have to press the info(

) button to be able to view the status of the

other LEDs.

For more information, see

“Info

button” on page 11

.

Ethernet LED

Wireless LED

Broadband LED (if you are using the

DSL Gateway

scenario)

Colour

State

Description

Green

Solid on

Network device connected to the Ethernet switch.

Blinking

Network device connected to the Ethernet switch and sending/receiving

data.

Off

No Ethernet connection on your local network or the status LEDs are

deactivated

Colour

State

Description

Green

Solid on

Wireless clients connected, no wireless activity

Blinking

Wireless clients connected, wireless activity

Off

No wireless clients connected or wireless access point disabled or the

status LEDs are deactivated

Colour

State

Description

Green

Solid on

DSL line synchronised

Blinking

Trying to detect carrier signal or pending DSL line synchronisation

Off

MediaAccess Gateway powered off or the status LEDs are deactivated.

14

1 GETTING STARTED

DMS-CTC-20110713-0016 v2.0

Broadband LED (if you are using the

Local Router

scenario)

Internet LED

Phone LED

DECT LED

WPS LED

For more information about WPS, see

“5.1 Connecting Your Wireless Client via WPS” on page 44

.

Colour

State

Description

Green

Solid on

Connected to the WAN device

Off

Not connected to the WAN device or the status LEDs are deactivated

Colour

State

Description

Green

Solid on

Connected to the Internet, no activity

Blinking

Connected to the Internet, sending/receiving data

Red

Solid on

Failed to setup the Internet connection

Off

No Internet connection or the status LEDs are deactivated

Colour

State

Description

Green

Solid on

Registered at your VoIP provider, no activity.

Blinking

Registered at your VoIP provider, activity.

Off

Not registered to your VoIP provider or the status LEDs are deactivated.

Colour

State

Description

Green

Solid on

DECT service up

Blinking

DECT activity or registering DECT clients

Off

DECT service down or the status LEDs are deactivated

Colour

State

Description

Green

Solid On

Client successfully registered via WPS

Orange

Blinking

WPS registration ongoing

Red

Blinking

Error occurred

15

1 GETTING STARTED

DMS-CTC-20110713-0016 v2.0

1.4

Preparing for the Installation

DSL service requirements

This section is only applicable if you are using your MediaAccess Gateway as DSL gateway. For more information, see

“1.2 User Scenarios” on page 5

.

Make sure that:



Your service provider activated the DSL service on your telephone line by your service provider.



You have the installation information (for example, user name, password, service profile,...) provided by your service

provider at hand.

Local connection requirements

Wireless connection

If you want to connect your computer using a wireless connection, your computer must be equipped with a WiFi-certified

wireless client adapter.

Wired connection

If you want to connect a computer using a wired connection, your computer must be equipped with an Ethernet Network

Interface Card (NIC).

Start with the installation

You are now ready to start with the installation of your MediaAccess Gateway.

16

1 GETTING STARTED

DMS-CTC-20110713-0016 v2.0

17

2 GUIDED INSTALLATION

DMS-CTC-20110713-0016 v2.0

2

Guided Installation

Introduction

In the guided installation, the Setup wizard on the Setup CD will assist you with the installation of your MediaAccess

Gateway.

If you do not want to use the Setup CD or if the Setup CD is not included in your package, follow the installation procedure

described in

“3 Manual Installation” on page 21

.

Requirements

To use the guided installation you must comply with the following requirements:



Your computer must run one of the following operating systems:



Microsoft Windows 7 and higher



Microsoft Windows 7 x64 and higher



Microsoft Windows Vista and higher



Microsoft Windows XP Service Pack 2 (SP2) and higher



Mac OS X 10.6 (Snow Leopard)



Mac OS X 10.5 (Leopard)



Mac OS X 10.4 (Tiger)



You must have administrative rights on your computer.

If you do not comply with these requirements, use the

“3 Manual Installation” on page 21

.

Running the Setup wizard

To start the Setup wizard:

1

Insert the Setup CD into your computer's CD- or DVD drive.

2

If your computer runs:



Microsoft Windows: The Setup CD starts automatically.

If the Setup CD does not autostart, see

“The Setup CD does not start automatically” on page 110

.



Mac OS X: Double-click

Menu

in the window with the content of the Setup CD.

3

Select the language of your choice and click

OK

.

4

The Setup wizard will now guide you through the installation of your MediaAccess Gateway.