1. Home
    2. /
  2. Manuals
    3. /
  3. Technicolor
    4. /
  4. TG788vn
    5. /
  5. 10
Page 46 / 159 Scroll up to view Page 41 - 45
44
5 THE MEDIAACCESS GATEWAY WIRELESS ACCESS POINT
DMS-CTC-20120510-0000 v1.0
5.4
Securing Your Wireless Connection
Introduction
You can protect the wireless communication between the wireless clients and your MediaAccess Gateway with a wireless key.
This means that:
Only clients which use the correct Network Name (SSID) and wireless key can connect to your network.
All data passing through your wireless access point is secured and encrypted.
Encryption types
Over the years a number of encryption types have been developed. The list below gives you an overview of the supported
encryption types ordered by descending security level; you will find the highest level of security at the top of the list:
WPA-PSK Encryption:
The wireless connection is secured with a pre-shared key that has been defined by the user. Wireless clients must be
configured with this key before they can connect to the MediaAccess Gateway. The MediaAccess Gateway supports the
following WPA-PSK versions (ordered by descending security):
WPA2-PSK:
The most recent and most secure version of WPA-PSK. Choose this version if you are sure that all your wireless clients
support WPA2-PSK.
WPA-PSK + WPA2-PSK
:
This is a mixed mode. In this mode WPA2-PSK, is the preferred encryption type but wireless clients do not support
WPA2-PSK, can still use WPA-PSK as encryption type. Choose this option if not all of your wireless clients support
WPA2-PSK or if you are not sure. Wireless clients that support WPA2-PSK will use WPA2-PSK, the others will use
WPA-PSK.
WPA-PSK
:
The first version of
WPA-PSK.
Choose this option if you are sure that none of your wireless clients support
WPA2-PSK.
WEP Encryption:
The least safe encryption type used for wireless connections. Like WPA-PSK it uses a user-defined key, but WEP has
been proven to have security issues.
Configuration
Proceed as follows:
1
Browse to the
MediaAccess Gateway GUI
.
For more information, see
“Accessing the MediaAccess Gateway GUI” on page 33
.
2
Under
Home Network
, click
Wireless
.
3
The
Wireless Access Point
page appears. In the upper-right corner, click
Configure
.
If you want to configure WPA2-PSK on the built-in wireless utility of Windows XP Service Pack 2 (SP2), you first
have to:
Upgrade your Windows XP to Service Pack 3.
- or -
Install the following update: http://support.microsoft.com/kb/917021
.
Although the MediaAccess Gateway allows you to use WEP or no security, we strongly advise against using one
of them! Use
WPA(2)-PSK
instead.
Page 47 / 159
45
5 THE MEDIAACCESS GATEWAY WIRELESS ACCESS POINT
DMS-CTC-20120510-0000 v1.0
4
In the
Security Mode
list, select one of the following modes:
WPA-PSK
WPA2-PSK
WPA-PSK + WPA2-PSK
For more information, see
“Encryption types” on page 44
.
5
In the
WPA-PSK Encryption Key
box, type a the key of your choice. The key must be in one of the following formats:
8 to 63 alphanumeric characters. For example: MyKey123
8 to 64 hexadecimal characters (characters from 0 to 9 and from A to F). For example: C54F48A5.
6
Click
Apply
.
7
Reconnect your wireless client(s) to the MediaAccess Gateway using these new security settings.
For more information, see
“5.1 Connecting Your Wireless Client via WPS” on page 40
or
“5.2 Connecting Your Wireless
Client without WPS” on page 42
.
Page 48 / 159
47
6 TELEPHONY
DMS-CTC-20120510-0000 v1.0
6
Telephony
Voice over IP (VoIP)
VoIP is a technology in which telephone calls are made over the Internet. This allows you to save on communication costs,
especially for long-distance calls.
The expensive solution
To be able to make your phone calls over the Internet you could either:
Buy an IP phone.
These IP phones are special phones that you can connect to your Internet Gateway.
Install VoIP software on your computer and make your phone calls via your computer.
The Technicolor solution
With the MediaAccess Gateway you can make both VoIP and traditional telephone calls using a traditional analogue phone.
If your MediaAccess Gateway is not powered, the traditional telephone network (if connected) will automatically selected.
This way you are still able to make emergency calls.
In this chapter
This chapter covers following topics:
Topic
Page
6.1
Setting Up Your Telephone Network
48
6.2
Address Book
51
6.3
Telephony Services
53
6.4
Viewing Call Logs
58
Page 49 / 159
48
6 TELEPHONY
DMS-CTC-20120510-0000 v1.0
6.1
Setting Up Your Telephone Network
Procedure
To set up your telephone network, follow these steps:
1
Connect your traditional phone(s), DECT base station or fax to the green
Phone
port(s) on the back panel of your
MediaAccess Gateway.
2
Configure the VoIP service on your MediaAccess Gateway.
For more information, see
“6.1.1 Configuring the MediaAccess Gateway VoIP Service” on page 49
.
Page 50 / 159
49
6 TELEPHONY
DMS-CTC-20120510-0000 v1.0
6.1.1
Configuring the MediaAccess Gateway VoIP Service
Introduction
If your VoIP service has not been configured yet, follow the instructions in this section.
How can I check if the VoIP service has already been configured?
If the
Phone
LED is:
Solid or blinking green then the VoIP service is configured correctly. No configuration is needed.
Off then telephony service is not configured (yet). Follow the instructions below.
Requirements
Your Internet connection must be up and running before you can configure Internet telephony.
Configuring the VoIP settings
Proceed as follows:
1
Enter the proxy and registrar settings
.
2
Enter your VoIP account settings
.
Enter the proxy and registrar settings
Proceed as follows:
1
Browse to the MediaAccess Gateway GUI.
For more information, see
“Accessing the MediaAccess Gateway GUI” on page 33
.
2
On the
Toolbox
menu, click
Telephony
.
3
In the
Navigation bar
, click
Expert configure
.
4
Complete the following fields based on the settings provided by your VoIP provider:
Proxy:
Type the URL (for example: sip.provider.com) or IP address of the proxy.
Registrar:
Type the URL (for example: sip.provider.com) or IP address of the registrar.
Registrar Port
and
Proxy Port
.
In most cases the default port (5060) will be used. Only change these values if your provider is using other port
numbers.
5
Click
Apply
.
Enter your VoIP account settings
Proceed as follows:
1
In the
Navigation bar
, click
Configure
.
2
Under
Service Configuration
, select
Enable Telephony
.
3
Under
Telephone Numbers
, complete the following fields:
SIP URI
:
The Uniform Resource Identifier (URI) of your SIP account (for example: 035051979, john.doe,...). This is the
telephone number that people have to dial to call you.
Username:
The user name of your VoIP account (for example: 035051979, john.doe,...).

Rate

3.5 / 5 based on 2 votes.

Popular Technicolor Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top