Page 31 / 106 Scroll up to view Page 26 - 30
25
3 MANUAL INSTALLATION
DMS-CTC-20110713-0024 v1.0
3.3.2
Setting up a Wired Connection
Requirements
Both your network device (for example, a computer, a gaming console,...) and MediaAccess Gateway must have a free
Ethernet port.
Your network device must be configured to obtain an IP address automatically. This is the default setting.
Ethernet cable
In your package, you will find a cable with yellow connectors. This is the Ethernet cable.
Procedure
Proceed as follows:
1
Connect one end of the Ethernet cable to one of the
yellow
Ethernet ports of your MediaAccess Gateway:
2
Connect the other end of the Ethernet cable to your network device.
3
Your network device is now connected to your network. No additional configuration is needed unless specified by your
service provider.
The MediaAccess Gateway does not support Power over Ethernet (PoE). All network devices that are connected
to the MediaAccess Gateway must be powered by their own power source.
Page 32 / 106
26
3 MANUAL INSTALLATION
DMS-CTC-20110713-0024 v1.0
3.4
Configure the MediaAccess Gateway
Introduction
If your service provider did not preconfigure your MediaAccess Gateway, you may have to configure the MediaAccess
Gateway via its Graphical User Interface (GUI).
Requirements
JavaScript must be enabled on your web browser (this is the default setting). For more information, consult the help of your
web browser.
Procedure
Proceed as follows:
1
Open your web browser.
2
The MediaAccess Gateway informs you that you have not yet configured your MediaAccess Gateway.
If this window does not appear, browse to http://dsldevice.lan
or to the IP address of your MediaAccess Gateway (by
default: 192.168.1.254
) and click
Technicolor Gateway
on the menu on the left-hand side.
3
Click
Setup my Technicolor Gateway
.
4
The
Easy Setup
wizard appears. This wizard will guide you through the configuration of your MediaAccess Gateway.
Click
Next
and follow the instructions.
Page 33 / 106
27
3 MANUAL INSTALLATION
DMS-CTC-20110713-0024 v1.0
3.5
Setting Up the 3G Fall-Back WAN Connection
Introduction
Many SOHO (Small Offices, Home Offices) and SME (Small/Medium Enterprises) businesses choose DSL as their access
technology for a Wide Area Network (WAN) connection because this is typically cheaper than using leased lines. A dropout
of a DSL line can however have expensive consequences due to inaccessibility of the Internet and E-mail. Therefore backup
solutions are available that provide an alternative path when the DSL line is down.
For example it is possible to switch to 2G / 3G mobile access technologies such as GPRS, UMTS, HSDPA, HSUPA,
HSPA+, WIMAX and LTE when internet connectivity is not available via the main WAN connection. By plugging a mobile
USB adapter into one of the USB ports of your MediaAccess Gateway, IP connectivity via a 2G / 3G network becomes
possible.
3G is an umbrella-term to indicate the third generation mobile telephony technology. The services associated with 3G
provide the ability to transfer both voice data and non-voice data. 3G networks are the successors of the 2G networks, such
as the GSM networks and provide new services and higher data transfer speeds.
What do I need?
To start using 2G / 3G as a connection on the MediaAccess Gateway, you need:
A mobile USB adapter
A registered Security Identity Module (SIM) card.
Configure 2G / 3G as WAN connection
Proceed as follows:
1
Configure your mobile connection.
For more information, see
“3.5.1 Managing your Mobile Connection with the MediaAccess Gateway GUI” on page 28
.
2
Insert your mobile USB adapter.
For more information, see
“3.5.2 Inserting a Mobile USB Adapter” on page 29
.
3
Now your mobile connection is up and ready to use.
Result
MediaAccess Gateway will automatically enable your 3G backup connection when
both
of the following conditions are met:
The main Internet connection has been unavailable for at least 60 seconds.
The MediaAccess Gateway received a request to access the Internet (for example, when browsing to an Internet web
site).
The MediaAccess Gateway will automatically disable the 3G connection in
either
of the following cases:
The main Internet connection is available again. In this case the MediaAccess Gateway switches back to the main Internet
connection.
No Internet traffic has been detected during the last 10 seconds. For example, you finished surfing the Internet.
Only use the mobile USB adapters provided by your service provider.
If you need to remove your mobile USB adapter, make sure the MediaAccess Gateway is powered off first.
Page 34 / 106
28
3 MANUAL INSTALLATION
DMS-CTC-20110713-0024 v1.0
3.5.1
Managing your Mobile Connection with the
MediaAccess Gateway GUI
Introduction
You can view and manage the parameters of your mobile connection via the MediaAccess Gateway GUI.
Procedure
To manage your mobile USB connection via the MediaAccess Gateway GUI:
1
Browse to the MediaAccess Gateway GUI.
For more information, see
“4.1.1 Access” on page 33
.
2
On the
Broadband Connection
menu, click
Internet Services
.
3
Click
View more...
for the mobile USB connection. The
Overview
page of the mobile USB connection is shown.
4
In the location bar, click
Configure
. The
Configure
page of the mobile connection appears.
5
Under
Mobile Information
, update the following fields if necessary:
APN
:
The public APN used to access the Internet, or the private APN to access a local network.
Operator Mode
:
2G / 3G / automatic (let the MediaAccess Gateway choose the best operator mode)
Pin
:
The PIN code of your SIM card.
6
Click
Apply
to apply your configuration changes.
Configuration changes via the MediaAccess Gateway GUI are automatically saved.
Page 35 / 106
29
3 MANUAL INSTALLATION
DMS-CTC-20110713-0024 v1.0
3.5.2
Inserting a Mobile USB Adapter
Procedure
Once the mobile connection is configured you can proceed as follows to insert the mobile USB adapter:
1
Power off the MediaAccess Gateway.
2
Insert your SIM card into the mobile USB adapter.
3
Plug the mobile USB adapter in (one of) the USB port(s) of your MediaAccess Gateway:
4
Power on the MediaAccess Gateway.
If you do not power off the MediaAccess Gateway first, the mobile USB adapter will not be detected.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top