Technicolor TD5130 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Technicolor

TD5130

Page 41 / 46 Scroll up to view Page 36 - 40

SETUP & USER GUIDE

DMS-CTC-20120508-0000 v1.0.

To Set up Security Settings

Click

Home Network > Interfaces >

WLAN

to open the Wireless Access Point page.

Click

Configure

on the upper-right corner of the screen.

Under the

Security

section, check the

Broadcast Network Name

to enable wireless devices to see

the SSID of your wireless network.

Encryption

, select an encryption method:



Disabled

— No encryption.



Use WEP Encryption

— To use WEP encryption.

▪

WEP Key Length

— Select the key length.

▪

WEP Encryption Key

— Type the desired encryption key. Users need to enter this passkey to

connect to the wireless network.



Use WPA

-PSK Encryption — To use a WPA-PSK encryption for more security.

▪

WPA-PSK Preshared Key

— Type the desired passkey. Users need to enter this passkey to

connect to the wireless network.

▪

WPA-PSK Version

— Select the WPA-PSK version to use.

Click

Apply

at the bottom of the page to save changes.

Page 42 / 46

SETUP & USER GUIDE

DMS-CTC-20120508-0000 v1.0.

To Set up MAC Filter

Click

Home Network > Interfaces >

WLAN

to open the Wireless Access Point page.

Click

Configure

on the upper-right corner of the screen.

Under the

MAC Filter

section,

MAC address

field, type the MAC address of a device to add to the

MAC filter.

Click

Add

. The MAC address is displayed on the MAC List table below. Repeat step 3 and 4 to add

more MAC addresses.

Restrict Mode

, select the restriction mode:



Disable

— To disable the MAC filter.



eny

— To deny Internet access to devices with MAC address listed on the MAC List table.



Allow

— To allow Internet access only to devices with MAC address listed on the MAC List table.

Click

Apply

to save changes.Appendix

Page 43 / 46

SETUP & USER GUIDE

DMS-CTC-20120508-0000 v1.0.

Appendix A

Wireless Considerations

Connection Performance

A number of factors affect wireless connections. To ensure high-range and stable connectivity, do the

following:

Keep the Wireless Gateway and other wireless devices away from obstructions, such as walls or

buildings. Each obstruction can reduce the range of a wireless device.

Keep the Wireless Gateway and other wireless devices away from devices that produce radio

frequency (RF) noise, such as microwave ovens or radios.

Keep the Wireless Gateway and other wireless devices away from any device operating on the 2.4GHz

frequency, such as cordless phones or remote controls.

Security Checklist

Wireless network signals can be intercepted easily. To prevent unauthorized users from connecting to

your wireless network, follow the guidelines below.

Change the default wireless network name.

Your device has a default Service Set Identifier (SSID) which is the wireless network name. Change

the SSID with a unique name to identify your network. The SSID can be up to 32 characters in length.

Change the default password.

Your device has a default password. You have to enter this password to change your network

settings. Change the password to prevent unauthorized users from hacking into your network and

changing the settings.

Enable MAC address filtering.

Your device supports Media Access Control (MAC) address filtering. You can assign a MAC address on

each computer that you want to connect to your wireless network. When MAC address filtering is

enabled, only the computers with the specified MAC addresses are allowed access.

Enable encryption

Your device supports Wired Equivalent Privacy (WEP), and Wi-Fi Protected Access (WAP/WPA2)

encryption. To ensure a high level of security, enable the highest security encryption and use strong

passphrases, avoid using words that can be found in the dictionary.

Page 44 / 46

SETUP & USER GUIDE

DMS-CTC-20120508-0000 v1.0.

Appendix B

Regulatory & Safety Information

Wireless LAN, Health and Authorization

Radio frequency electromagnetic energy is emitted from Wireless LAN devices. The energy levels of

these emissions however are far much less than the electromagnetic energy emissions from wireless

devices like for example mobile phones. Wireless LAN devices are safe for use frequency safety

standards and recommendations. The use of Wireless LAN devices may be restricted in some situations

or environments for example:

▪

Onboard airplanes, or

▪

In an explosive environment, or

▪

In case the interference risk to other devices or services is perceived or identified as harmful

In case the policy regarding the use of Wireless LAN devices in specific organizations or environments

(e.g. airports, hospitals, chemical/oil/gas industrial plants, private buildings etc.) is not clear, please

ask for authorization to use these devices prior to operating the equipment.

Disclaimers

Installation and use of this Wireless LAN device must be in strict accordance with the instructions

included in the user documentation provided with the product. Any changes or modifications made to

this device that are not expressly approved by the manufacturer may void the user’s authority to

operate the equipment. The Manufacturer is not responsible for any radio or television interference

caused by unauthorized modification of this device, of the substitution or attachment. Manufacturer

and its authorized resellers or distributors will assume no liability for any damage or violation of

government regulations arising from failing to comply with these guidelines.

FCC (Federal Communications Commission) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

▪

Reorient or relocate the receiving antenna.

▪

Increase the separation between the equipment and receiver.

▪

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

▪

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment. This device complies with Part 15

of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause interference, and

This device must accept any interference, including interference that my cause undesired operation

of this device.

Page 45 / 46

SETUP & USER GUIDE

DMS-CTC-20120508-0000 v1.0.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

The availability of some specific channels and/or operational frequency bands are country dependent

and are firmware programmed at the factory to match the intended destination. The firmware setting

is not accessible by the end user.

CE statement

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following

test methods have been applied in order to prove presumption of conformity with the essential

requirements of the R&TTE Directive 1999/5/EC:

EN60950-1: 2006

Safety of Information Technology Equipment

EN 50385: 2002

Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for

wireless telecommunication systems with the basic restrictions or the reference levels related to human

exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public

EN 300 328 V1.7.1 (2006-10)

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data

transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques;

Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive

EN 301 489-1 V1.8.1 (2008-04)

Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)

standard for radio equipment and services; Part 1: Common technical requirements

EN 301 489-17 V2.1.1 (2009-05)

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)

standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems.

This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member

states and EFTA countries, except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain

authorization to use the device for setting up outdoor radio links and/or for supplying public access to

telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF

output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed

information the end-user should contact the national spectrum authority in France.

Rate

Popular Technicolor Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share