1. Home
    2. /
  2. Manuals
    3. /
  3. Technicolor
    4. /
  4. TC8305C
    5. /
  5. 5
Page 21 / 68 Scroll up to view Page 16 - 20
13
2 SETUP
DMS-CTC-20130228-0000 v1.0
2 Setup
Setup procedure
Complete the following steps to setup the Gateway:
1
Connect your Gateway to your service provider’s network.
For more information, see
“2.1 Connect the Gateway to your service provider’s network” on page 14
.
2
Power on the Gateway.
For more information, see
“2.2 Power on the Gateway” on page 15
.
3
Connect your wired devices to the Gateway.
For more information, see
“2.3 Connect your wired devices” on page 16
.
4
Connect your wireless devices to the Gateway.
For more information, see
“2.4 Connect your wireless devices” on page 17
.
5
Connect your phones.
For more information, see
“2.5 How to connect your phone” on page 24
.
Optional configuration
After completing the setup procedure, the Gateway is ready for use. Optionally, you can further configure the Gateway to
your needs (for example, change the wireless security) using the Gateway’s Admin Tool.
For more information, see
“3 Admin Tool” on page 25
.
Page 22 / 68
14
2 SETUP
DMS-CTC-20130228-0000 v1.0
2.1
Connect the Gateway to your service provider’s
network
Introduction
This section helps you to connect the Gateway to your service provider’s network.
Connecting the cables
Proceed as follows:
1
Take one end of the coaxial cable and connect it to your cable splitter.
2
Connect the other end to the
Cable
port of the Gateway.
105+
SN: 8700383561
CM MAC : 00
100ABCD
E-MTA MAC : 0022
100ABCD
WAN MAC : 0044
100ABCD
Page 23 / 68
15
2 SETUP
DMS-CTC-20130228-0000 v1.0
2.2 Power on the Gateway
Procedure
Proceed as follows:
1
Take the power cord that is included with your Gateway.
2
Connect the small end of the power cord to the
Power
port on the back of the Gateway.
3
Plug the other end of the power cord into an electrical outlet.
4
Wait at least two minutes to allow the Gateway to complete the start up phase.
105+
SN: 8700383561
CM MAC : 00
100ABCD
E-MTA MAC : 0022
100ABCD
WAN MAC : 0044
100ABCD
Page 24 / 68
16
2 SETUP
DMS-CTC-20130228-0000 v1.0
2.3 Connect your wired devices
Requirements
Both your network device (for example, a computer, a gaming console, etc.) and Gateway must have a free Ethernet
port.
Your network device must be configured to obtain an IP address automatically. This is the default setting.
All Ethernet ports on the Gateway are Gigabit Ethernet ports and have a maximum speed of 1 Gbps (Gigabit per second).
Procedure
Proceed as follows:
1
Take the yellow Ethernet cable that is included in your box.
2
Plug one end of the Ethernet cable into one of the
yellow
Ethernet ports on the back of the Gateway:
3
Plug the other end of the Ethernet cable into the Ethernet port of your network device.
4
Your network device is now connected to your network. Use the same procedure to connect your other Ethernet devices
(computers, network printers and so on).
105+
SN: 8700383561
CM MAC : 00
100ABCD
E-MTA MAC : 0022
100ABCD
WAN MAC : 0044
100ABCD
Page 25 / 68
17
2 SETUP
DMS-CTC-20130228-0000 v1.0
2.4 Connect your wireless devices
Introduction
The Gateway has an integrated 2.4 GHz access point that allows you to connect wireless devices to your home network.
Procedure
To connect your device via:
Via WPS, proceed with
“2.4.1 How to connect your wireless client via WPS” on page 18
.
By manually entering the settings, proceed with
“2.4.2 How to manually connect your wireless client” on page 20
.

Rate

4.5 / 5 based on 2 votes.

Popular Technicolor Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top