Page 56 / 89 Scroll up to view Page 51 - 55
56
Local network configuration
Gigaset SE587 WLAN dsl / eng / A31008-N1083-L171-1-7619 / configure_network.fm / 12.12.2007
Schablone 2004_08_26
Obtaining an IP address automatically
ì
If
Obtain an IP address automatically
has been activated, your PC is already
configured for DHCP. Click
Cancel
and close the following windows with
OK
to start
your network configuration.
You may be prompted to insert your Windows installation CD. Follow the
instructions in the installation procedure.
Once the copying procedure is completed, you will be prompted to reboot your
system.
ì
Click
Yes
. The PC will then be shut down and rebooted.
ì
If
Obtain an IP address automatically
has not been activated, activate this option
now.
ì
Open the
Gateway
tab and remove any entries in the
Installed gateways
list.
ì
Open the
DNS Configuration
tab.
ì
Select
Disable DNS
.
Page 57 / 89
57
Local network configuration
Gigaset SE587 WLAN dsl / eng / A31008-N1083-L171-1-7619 / configure_network.fm / 12.12.2007
Schablone 2004_08_26
ì
Click
OK
.
ì
Finish the network configuration with
OK
.
You may be prompted to insert your Windows installation CD. Follow the
instructions in the installation procedure.
Once the copying procedure is completed, you will be prompted to reboot your
system.
ì
Click
Yes
. The PC will then be shut down and rebooted.
Assigning an IP address statically
If the DHCP server of your router/access point is not active or the PC is to be assigned a
static IP address for other reasons, the following settings must be made:
ì
Select the option
Specify an IP address
on the
IP Address
tab.
ì
Enter the IP address for the PC in the
IP Address
field.
ì
Enter the subnet mask to be used in your network in the
Subnet Mask
field. You can
check these settings if necessary in the LAN configuration for your router/access
point.
ì
Open the
Gateway
tab and enter the IP address of the router/access point in the
New gateway
field or choose this, if available, from the
Installed gateways
list.
ì
Open the
DNS Configuration
tab.
ì
Select
Enable DNS
.
ì
Enter the IP address for the router/access point in the
DNS Server Search Order
field and click
Add
.
ì
Click
OK
.
ì
Finish the network configuration with
OK
.
You may be prompted to insert your Windows installation CD. Follow the
instructions in the installation procedure.
Once the copying procedure is completed, you will be prompted to reboot your
system.
ì
Click
Yes
. The PC will then be shut down and rebooted.
Page 58 / 89
58
Local network configuration
Gigaset SE587 WLAN dsl / eng / A31008-N1083-L171-1-7619 / configure_network.fm / 12.12.2007
Schablone 2004_08_26
Network configuration with Mac OS X
Showing networks
To configure your network click the apple icon
on the left side of the menu bar
and choose
System Preferences
.
ì
Choose
Network
.
ì
Choose from the list
Show
the option
AirPort
, if your Mac is connected wirelessly to
the network and choose the option
Built-in Ethernet
if your Mac is connected via
cable.
You can start all actions for your network configuration from here.
Page 59 / 89
59
Local network configuration
Gigaset SE587 WLAN dsl / eng / A31008-N1083-L171-1-7619 / configure_network.fm / 12.12.2007
Schablone 2004_08_26
Changing the settings for IP addresses
The IP addressing settings can be checked and modified as follows:
Obtaining an IP address automatically
If the DHCP server of your router/access point is active and your Mac is to obtain its IP
address automatically, you must choose the option
DHCP
from the
Configure IPv4
list.
ì
Check whether this option is selected and select it if necessary.
ì
Click
Apply Now
to save your network configuration.
Assigning an IP address statically
If the DHCP server of your router/access point is not active or your Mac is to be assigned
a static IP address for other reasons, the following settings must be made:
Page 60 / 89
60
Local network configuration
Gigaset SE587 WLAN dsl / eng / A31008-N1083-L171-1-7619 / configure_network.fm / 12.12.2007
Schablone 2004_08_26
ì
Select the tab
TCP/IP
.
ì
Choose the option
Manually
from the
Configure IPv4
list.
ì
Enter the IP address for your Mac in the
IP Address
field.
ì
Enter the subnet mask to be used in your network in the
Subnet Mask
field. You can
check these settings if necessary in the LAN configuration for your router/access
point.
ì
Enter the IP address for the router/access point in the
Router
field.
ì
Select the option
Use the following DNS server addresses
.
ì
Enter the IP address for the router/access point in the
DNS Servers
field.
ì
Click
Apply Now
.
Selecting a computer name
Your Mac is assigned a name during installation. To change the name assignment, you
have to:
ì
Click the Apple icon
on the left side of the menu bar and choose
System Preferences
.
ì
Click
Sharing
.
The name of your Mac is shown is the
Computer Name
field.
ì
Click
Edit
.
ì
Enter the name the Mac is to appear under in the network. This name must be
unique within the network.
ì
Click
OK
.
Synchronising TCP/IP settings with the Gigaset SE587 WLAN
dsl
If you have made changes to the network configuration on your computer or have
connected it to a different Gigaset SE587 WLAN dsl, you may have to release the old
TCP/IP settings and synchronise them with the settings for your router/access point. The
software for your wireless adapter normally provides synchronisation functions. If this
is not the case, you can use the following Windows operating system resources.
Windows Vista, Windows XP, Windows 2000
ì
Open the Windows command prompt. From the Start menu of the Windows taskbar,
click
Start
All Programs
Accessories
Command Prompt
.
ì
In the
Command Prompt
window, enter the
ipconfig /release
command and press the ENTER key.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top