Page 21 / 185 Scroll up to view Page 16 - 20
23
First steps
Line
On
One of the connected phones' receivers has been lifted for a
call (fixed network telephony).
Flashing
The phone is ringing and a fixed network call is being
received or someone is waiting on the line.
Off
There is currently no fixed network connection.
Online
On
Connection to the Internet has been established.
Off
There is no Internet connection.
USB
On (green)
A device is connected to the Giga762SX WLAN dsl via the
USB port.
Flashing
The device connected on the USB port is using too much
power (see page 163).
Off
There is no device connected.
LAN1 –
LAN4
On
A device is connected to the relevant LAN port.
Flashing
The relevant LAN port is sending or receiving data (traffic).
Off
There is no device connected.
WLAN
In normal operation
On
The radio interface is activated, no data transmission at
present.
Flashing
The Giga762SX WLAN dsl is sending or receiving data on the
radio interface.
Off
The radio interface is deactivated.
During WPS registration
On (300 sec)
WPS registration was successful.
Flashing
slowly
WPS registration is in progress.
Flashing
quickly
WPS registration was not successful.
Flashing
quickly with
interruption
More than one client tried to register.
VoIP
On
At least one port is configured for VoIP and VoIP access is
registered with the provider.
Flashing
A call is currently being made via the Internet.
Off
There is currently no connection for Internet telephony or no
VoIP port has been configured.
LED
State
Status
Page 22 / 185
24
First steps
The Giga762SX WLAN dsl can be set up in any suitable location in the home or office.
You do not need any special wiring. However, you should comply with the following
guidelines:
u
Operate the Giga762SX WLAN dsl only indoors within a temperature range of 0 to
+40 °C. Do not position the Giga762SX WLAN dsl near sources of heat. Do not cover
the ventilation slots. High temperatures can damage the device.
u
A mains socket for 220/230 V~ and a connection socket for the splitter or LAN must
be available in the place where you set up the Giga762SX WLAN dsl.
u
Do not position the device in the immediate vicinity of stereo equipment, TV sets,
microwave ovens or the like. This may cause interference.
u
Position the Giga762SX WLAN dsl so that it is as near to the centre of your wireless
network as possible. The general rule is: The higher you place the antennae, the bet-
ter the performance. Make sure that the place where you position the Giga762SX
WLAN dsl offers optimum reception throughout the house, apartment or office.
u
Position the Giga762SX WLAN dsl so that it cannot fall down and damage the anten-
nae. Position the Giga762SX WLAN dsl on a non-slip surface.
u
Do not place the Giga762SX WLAN dsl on any furniture surface that could be
affected by the heat from the device.
u
Lay the cables so that nobody can trip over them. You should not cover the cables
with anything.
Phone 1/
Phone 2
On
The receiver of the phone connected to the port has been
lifted.
Flashing
The phone is ringing and a call is being received or a call is
being conducted.
Off
No phone is connected or the connection is idle.
Please remember:
Network connections (LAN) via cables and telephone lines may only be set up with
the Giga762SX WLAN dsl within enclosed rooms.
LED
State
Status
Page 23 / 185
25
First steps
Connecting and activating the Giga762SX WLAN dsl
Ports on the rear panel
The rear panel of the Giga762SX WLAN dsl houses the ports.
Element
Description
PWR
Socket for the mains adapter supplied
Warning
: Using the wrong power supply unit may damage the
Giga762SX WLAN dsl.
Depending on the device variant, there may be an on/off button
beside the PWR port.
Scan
Button for WPS activation. You can use this button to quickly establish
a secure wireless connection to PCs. The same function is provided via
the device’s user interface (see page 87).
Note:
You can deactivate the
Scan
(registration) button to protect it
against unauthorised access (see page 125).
USB
USB port for printer or USB memory.
Page 24 / 185
26
First steps
Reset button
The underside of the Giga762SX WLAN dsl houses the reset button.
Reboot function
: Press and hold the right end of the button for more than 1 second but
less than 5 seconds to reboot the device. This does not affect the configuration settings.
Reset function
: Press and hold the right end of the button for at least 5 seconds to
return all settings to factory settings.
Warning
: This will clear all the configuration settings you have made since the initial
startup.
Updated firmware will not be affected.
LAN1 –
LAN4/WAN
(yellow)
Four 10/100
Mbps
switch ports with automatic recognition (RJ-45).
You can connect up to four devices with Ethernet ports (such as PCs, a
Hub
or
Switch
).
You can connect an external modem (e.g. a VDSL or cable modem) to
the LAN4 port. The integrated ADSL modem is then deactivated. You
will find additional information on the configuration settings on
page 62.
ADSL
(black)
DSL socket for connecting the integrated modem to the DSL port of the
splitter
Line
(green)
Socket for connecting the phone line to the telephone port on the
splitter
Phone1/2
Sockets for connecting two phones, fax or answering machine
Element
Description
Reset button
Label with WPA key
„SX762xxxxxx“
Page 25 / 185
27
First steps
Connecting to the splitter data port
You can operate the Giga762SX WLAN dsl in two different operating modes in order to
set up an Internet connection:
with an integrated ADSL modem
with an external modem, such as a VDSL or cable modem
Using the integrated ADSL modem
ì
Connect the
ADSL
port (
black
) on the Giga762SX WLAN dsl to the ADSL socket on
the splitter. To do this, use the DSL cable supplied (
black
).
ì
Connect the splitter with one oft the RJ11 sockets on the top of the power supply.
ì
Connect the other RJ11 socket on the top of the power supply with your phone con-
nector. To do this, use the RJ11 cable supplied.
Splitter
DSL cable
(black)
Power supply

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top