1. Home
    2. /
  2. Manuals
    3. /
  3. RadioLabs
    4. /
  4. O2Storm
    5. /
  5. 7
Page 31 / 77 Scroll up to view Page 26 - 30
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
23
Broadband Router access capability.
Comment
Fill in the comment tag for the registered client.
Apply Changes
Click the
Apply Changes
button to register the client to
new configuration setting.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
Current Access Control
List
It shows the registered clients that are allowed to link to
this WLAN Broadband Router.
Delete Selected
Click to delete the selected clients that will be access
right removed from this WLAN Broadband Router.
Delete All
Click to delete all the registered clients from the access
allowed list.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
3.3.8
WDS Settings
Wireless Distribution System uses wireless media to communicate with other
APs, like the Ethernet does. To do this, you must set these APs in the same
channel and set MAC address of other AP that you want to communicate with in
the table and then enable the WDS.
Screen snapshot – WDS Setup
Page 32 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
24
Item
Description
Enable WDS
Click the check box to enable wireless distribution
system. Refer to 4.21 What is Wireless Distribution
System (WDS)?
MAC Address
Fill in the MAC address of AP to register the wireless
distribution system access capability.
Comment
Fill in the comment tag for the registered AP.
Apply Changes
Click the
Apply Changes
button to register the AP to new
configuration setting.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
Set Security
Click button to configure wireless security like
WEP(64bits), WEP(128bits), WPA(TKIP), WPA2(AES)
or
None
Show Statistics
It shows the TX, RX packets, rate statistics
Delete Selected
Click to delete the selected clients that will be removed
from the wireless distribution system.
Delete All
Click to delete all the registered APs from the wireless
distribution system allowed list.
Reset
Click the
Reset
button to abort change and recover the
previous configuration setting.
I
WDS Security Setup
Requirement: Set [Wireless]->[Basic Settings]->[Mode]->AP+WDS
This page is used to configure the wireless security between APs. Refer to
3.3.6 Wireless Security Setup
.
Page 33 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
25
Screen snapshot – WDS Security Setup
II
WDS AP Table
This page is used to show WDS statistics
Screen snapshot – WDS AP Table
Item
Description
MAC Address
It shows the MAC Address within WDS.
Tx Packets
It shows the statistic count of sent packets on the wireless
LAN interface.
Tx Errors
It shows the statistic count of error sent packets on the
Wireless LAN interface.
Rx Packets
It shows the statistic count of received packets on the
wireless LAN interface.
Page 34 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
26
Tx Rare (Mbps)
It shows the wireless link rate within WDS.
Refresh
Click to refresh the statistic counters on the screen.
Close
Click to close the current window.
3.3.9
Site Survey
This page is used to view or configure other APs near yours.
Screen snapshot – Wireless Site Survey
Item
Description
SSID
It shows the SSID of AP.
BSSID
It shows BSSID of AP.
Channel
It show the current channel of AP occupied.
Type
It show which type AP acts.
Encrypt
It shows the encryption status.
Signal
It shows the power level of current AP.
Select
Click to select AP or client you’d like to connect.
Refresh
Click the
Refresh
button to re-scan site survey on the
screen.
Connect
Click the
Connect
button to establish connection.
3.3.10
LAN Interface Setup
This page is used to configure the parameters for local area network that
connects to the LAN ports of your WLAN Broadband Router. Here you may
Page 35 / 77
USER’S MANUAL OF WLAN BROADBAND ROUTER
Version: 2.1
27
change the setting for IP address, subnet mask, DHCP, etc.
Screen snapshot – LAN Interface Setup
Item
Description
IP Address
Fill in the IP address of LAN interfaces of this WLAN
Access Point.
Subnet Mask
Fill in the subnet mask of LAN interfaces of this WLAN
Access Point.
Default Gateway
Fill in the default gateway for LAN interfaces out going
data packets.
DHCP
Click to select
Disabled
,
Client
or
Server
in different
operation mode of wireless Access Point.
DHCP Client Range
Fill in the start IP address and end IP address to allocate a
range of IP addresses; client with DHCP function set will
be assigned an IP address from the range.
Show Client
Click to open the
Active DHCP Client Table
window that
shows the active clients with their assigned IP address,
MAC address and time expired information.
[Server
mode only]

Rate

3.5 / 5 based on 2 votes.

Popular RadioLabs Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top