Prolink Hurricane-9000P Router Manual PDF (Setup & Configuration Guide)

Page 21 / 36 Scroll up to view Page 16 - 20

21

Section Four: Web-Based Management

4.3.7

Virtual Server

The

Virtual Server (Port Forwarding)

page allows users to set the

configuration of Virtual Server. If any specific local PCs need to be

mapped to the UDP/TCP port on WAN side, please input the mappings

here.

For Example,

If you want to forward FTP to your 10.0.0.20 server (set to static IP):

Public Port Start

: 21,

Public Port End

: 21,

Private Port:

21

Port Type: TCP

Host IP Address: 10.0.0.20

Customized

Port

TCP

UDP

Application

Web server

80

Yes

FTP server

21

Yes

No

SMTP (outgoing)

25

Yes

POP3 (incoming)

110

Yes

Page 22 / 36

22

4.3.8 Bridge Filtering

The

Bridge Filtering

page allows users to set the configuration of IP

filtering.

Source MAC

: When the bridge filtering is enabled, enter the Source MAC

address, select Block and click Add. Then all incoming WAN and LAN

Ethernet packets matched with this source MAC address will be filtered out.

If the Forward is selected, then the packets will be forwarded to the

destination PC.

Destination MAC

: When the bridge filtering is enabled, enter the

Destination MAC address, select Block and click Add. Then all incoming

WAN and LAN Ethernet packets matched with this destination MAC address

will be filtered out. If the Forward is selected, then the packets will be

forwarded to the destination PC.

Type:

Enter the hexadecimal number for the Ethernet type field in

Ethernet_II packets.

For example

,

If you want to block MAC address: 000002fa6fab to access the internet:

Source MAC: 000002fa6fab

Type: 0800

Remark: to check your PC's MAC address, ipconfig /all under DOS mode.

Type 0800: Internet

Protocol, for others, pls. check with your administrator.

Section Four: Web-Based Management

Page 23 / 36

23

4.3.9 DNS Configuration

The

DNS Configuration

page allows users to set the configuration

of DNS proxy. It supports the DNS proxy function. For the DHCP

requests from local PCs, the DHCP server will set the LAN port IP as

the default DNS server. Thus, all DNS query messages will come into

LAN port first. The DNS proxy on the ADSL modem recorded the

available DNS servers, and forward DNS query messages to one of DNS

server.

Disable DNS Proxy:

The LAN port does not process the DNS query

message. For the DHCP requests from local PCs, the DHCP server will

set the user-configured preferred DNS sever or alternate DNS server

whichever is available as the DNS server. Then all DNS query messages

will be directly sent to the DNS servers.

Use Auto Discovered DNS Servers Only:

The DNS proxy will store

the DNS server IP addresses obtained from DHCP client or PPP into the

table. And all DNS query messages will be sent to one of the dynamically

obtained DNS servers.

Use User Configured DNS Servers Only:

The DNS proxy will use the

user-configured preferred DNS server and alternate DNS server. And all

DNS query message will be sent to one of DNS servers. Enter the DNS IP

in the Preferred DNS Server and Alternate DNS Server fields.

Auto Discovery + User Configured:

The DNS proxy’s table has all the

IP addresses of dynamically obtained and user configured DNS servers.

Section Four: Web-Based Management

Page 24 / 36

24

4.3.10 ADSL Configuration

The

ADSL Configuration

page allows users to set the configuration

for ADSL protocols...

Trellis:

Trellis Code. By default, it is always enabled.

Handshake Protocol:

This is for the ADSL handshake protocol.

Wiring Selection:

The wiring selection for the RJ-11.

Bit Swapping:

Disable by default.

4.3.11

Route Table

The

Route Table

page displays routing table and allows users to

manually enter the routing entry. The interface br0 means the Ethernet/

USB interface; lo0 means the loopback interface.

Section Four: Web-Based Management

Page 25 / 36

25

4.3.12 Learned MAC Table

The Learned MAC Table

page shows the current learned Bridge MAC

table.

4.3.13 RIP Configuration

The RIP Configuration

page allows the user to set the configuration

for the system wide configuration of RIP. The actual RIP configuration is

in the RIP Per Interface Configuration.

Section Four: Web-Based Management

Rate

Popular Prolink Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share