Page 51 / 68
Scroll up to view Page 46 - 50
PROLiNK
®
H5004N User Manual
www.prolink2u.com
Version 1.00 (Jan’10)
50
4.7.3
System Log
This page shows the system log.
4.7.4
Password
The first time you log into the system, you use the default password. There are two-level
logins: admin and user. The admin and user password configuration allows you to change
the password for administrator and user.
Fields in this page:
Field
Description
User Name
Selection of user levels are: admin and user.
Old Password
Enter the old password for this selected login.
New Password
Enter the new password here.
Confirmed Password
Enter the new password here again to confirm.
Page 52 / 68
PROLiNK
®
H5004N User Manual
www.prolink2u.com
Version 1.00 (Jan’10)
51
4.7.5
Upgrade Firmware
To upgrade the firmware for the DSL device:
•
Click the Browse button to select the firmware file.
•
Confirm your selection.
•
Click the Upload button to start upgrading.
IMPORTANT!
Do not turn off your DSL device or press the Reset button while this procedure is in
progress.
4.7.6
ACL
The Access Control List (ACL) is a list of permissions attached to the DSL device. The list
specifies who is allowed to access this device. If ACL is enabled, all hosts cannot access
this device except for the hosts with IP address in the ACL table.
1.
LAN – You can enable LAN ACS Switch to allow/block the PC to access the
Modem
Page 53 / 68
PROLiNK
®
H5004N User Manual
www.prolink2u.com
Version 1.00 (Jan’10)
52
2.
WAN – you can enable web(http)/telenet/ftp/tftp/snmp/ping for WAN access
4.7.7
Time Zone
Simple Network Timing Protocol (SNTP) is a protocol used to synchronize the system time
to the public SNTP servers. The DSL device supports SNTP client functionality in
compliance with IETF RFC2030. SNTP client functioning in daemon mode which issues
sending client requests to the configured SNTP server addresses periodically can
configure the system clock in the DSL device
Page 54 / 68
PROLiNK
®
H5004N User Manual
www.prolink2u.com
Version 1.00 (Jan’10)
53
Fields in this page:
Field
Description
Current Time
The current time of the specified time zone. You can set the current time by
yourself or configured by SNTP.
Time Zone Select
The time zone in which the DSL device resides.
Enable SNTP client
update
Enable the SNTP client to update the system clock.
SNTP server
The IP address or the host name of the SNTP server. You can select from the list
or set it manually.
4.7.8
TR-069 Config (Optional)
TR-069 is a protocol for communication between a CPE and Auto-Configuration Server
(ACS). The CPE TR-069 configuration should be well defined to be able to communicate
with the remote ACS.
Page 55 / 68
PROLiNK
®
H5004N User Manual
www.prolink2u.com
Version 1.00 (Jan’10)
54
Fields in this page:
ACS Field
Description
URL
ACS URL. For example,
User Name
The username the DSL device should use when connecting to the ACS.
Password
The password the DSL device should use when connecting to the ACS.
Periodic Inform Enable
When this field is enabled, the DSL device will send an Inform RPC to the ACS
server at the system startup, and will continue to send it periodically at an
interval defined in Periodic Inform Interval field; When this field is disabled, the
DSL device will only send Inform RPC to the ACS server once at the system
startup.
Periodic Inform Interval
Time interval in second to send Inform RPC.
Connection Request Field
Description
User Name
The username the remote ACS should use when connecting to this device.
Password
The password the remote ACS should use when connecting to this device.
Path
The path of the device ConnectionRequestURL. The device
ConnectionRequestURL should be configured based on the Device_IP, Path
and Port as follows: http://Device_IP:Port/Path
Port
The port of the device ConnectionRequestURL.
19216811.live