1. Home
    2. /
  2. Manuals
    3. /
  3. Ping-Communication
    4. /
  4. RGW208EN
    5. /
  5. 17
Page 81 / 92 Scroll up to view Page 76 - 80
Connection Type:
The Internet connection type that is being used.
StreamEngine:
Tells whether or not this feature is active
Cable Status:
Displays whether the network cable is connected or disconnected.
Network Status:
Displays whether the network has been established.
Connection Up Time:
If a connection has been successfully established, this field
displays how long the connection has been active.
DHCP Connection
Clicking the
DHCP Release
button unassigns the router's IP address. The
router will not respond to IP messages from the WAN side until you click the
DHCP Renew
button or power-up the router again. Clicking the
DHCP Renew
button causes the router to request a new IP address from the ISP's server.
PPPoE, PPTP, L2TP Connection
Depending on whether the WAN connection is currently established, you can
click either the
Connect
to attempt to establish the WAN connection or the
Disconnect
to break the WAN connection.
MAC Address:
The MAC address that is seen over the Internet.
IP Address:
The IP address being used on the WAN port.
Subnet Mask:
The subnet mask used on the WAN port.
Default Gateway:
The default gateway of the WAN port.
Primary DNS Server:
The Primary DNS Server address.
Secondary DNS Server:
The Secondary DNS Server address.
Page 81 of 92
Page 82 / 92
6.1.3
LAN
MAC Address:
The MAC address displayed for your local area network.
IP Address:
The IP address of the router on your local area network.
Subnet Mask:
The subnet mask of the router on your local area network.
Auto IP Address:
If no IP address is assigned to this device, this IP address is
used.
DHCP Server:
Indicates if the router is acting as a DHCP server on the local area
network.
6.1.4
VoIP Line Status
Show if the lines are enabled and/or in use. Idle status is when lines are active but
not in use.
6.1.5
LAN Computers & IGMP Multicast memberships
Page 82 of 92
Page 83 / 92
This section continually updates to show all DHCP enabled computers and devices
connected to the LAN side of your router. The detection "range" is limited to the
address range as configured in DHCP Server. Computers that have an address
outside of this range will not show. If the DHCP Client (i.e. a computer configured to
"Automatically obtain an address") supplies a Host Name then that will also be
shown. Any computer or device that has a static IP address that lies within the
detection "range" may show, however its host name will not.
If IGMP is enabled, this section shows all multicast groups of which any LAN devices
are members.
6.2
Wireless
View the wireless clients that are connected to the router. (A client might linger in
the list for a few minutes after an unexpected disconnect.)
MAC Address:
The Ethernet ID (MAC address) of the wireless client.
IP Address:
The LAN-side IP address of the client.
Mode:
The transmission standard being used by the client. Values are 11a, 11b, 11g, or
11n for 802.11a, 802.11b, 802.11g, or 802.11n respectively.
Rate:
The actual transmission rate of the client in megabits per second.
Signal:
This is a relative measure of signal quality. The value is expressed as a
percentage of theoretical best quality. Signal quality can be reduced by distance, by
interference from other radio-frequency sources (such as cordless telephones or
neighboring wireless networks), and by obstacles between the router and the wireless
device.
6.3
Routing
This page displays the routing details configured for the router.
A gateway value of 0.0.0.0 means there is no next hop. The IP address is directly
connected to the router on the interface specified, LAN or WAN. A value of 0.0.0.0 in
both the destination IP and netmask means that this is the default route.
Page 83 of 92
Page 84 / 92
6.4
Logs
The router automatically logs (records) events of possible interest in it’s internal
memory. If there isn’t enough internal memory for all events, logs of older events
are deleted but logs of the latest events are retained. The
Logs
option allows you to
view the router logs. You can define what types of events you want to view and the
level of the events to view. This router also has external
Syslog Server
support so
you can send the log files to a computer on your network that is running a
Syslog
utility.
Page 84 of 92
Page 85 / 92
6.4.1
Log Options
What to View:
You can select the types of messages that you want to display from
the log. Firewall & Security, System, and Router Status messages can be selected.
View Levels:
There are three levels of message importance: Informational,
Warning, and Critical. Select the levels that you want displayed from the log.
Apply Log Settings Now:
Will filter the log results so that only the selected options
appear.
6.4.2
Log Details
Refresh:
Updates the log details on the screen so it displays any recent activity.
Clear:
Clears all of the log contents.
Email Now:
This option will send a copy of the router log to the email address
configured in the
Tools > Email
screen.
Save Log:
This option will save the router to a log file on your computer
6.5
Statistics
The
Statistics
page display all of the LAN and WAN packet transmit and receive
statistics.
Page 85 of 92

Rate

3.5 / 5 based on 2 votes.

Popular Ping-Communication Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top