Page 106 / 146
Scroll up to view Page 101 - 105
100
4.6 TOOLS
TOOLS:
The
TOOLS
page allows you to save the configuration, restart the device, update the
firmware/image code, setup user and remote log information and run ping/test of the WL-8064ARM Wireless
ADSL2/2+ Router.
±
System Commands:
Save the current configuration, restart the WL-8064ARM Wireless
ADSL2/2+ Router and restore to factory defaults setting.
±
Remote Log:
Setup Remote Log Information.
±
User Management:
Configure user name and password.
±
Update Gateway:
Upgrade the WL-8064ARM Wireless ADSL2/2+ Router firmware.
±
Ping Test:
Run a ping test.
±
Modem Test:
Check whether the modem with a specific connection is properly connected to the
network.
Page 107 / 146
101
4.6.1 TOOLS - System Commands
The System Commands page allow you to carry out basic system actions.
±
Restart:
Use this button to restart the WL-8064ARM Wireless ADSL2/2+ Router system.
NOTE:
You will be redirected to the WL-8064ARM Wireless ADSL2/2+ Router Homepage after
the unit has successfully rebooted.
±
Restart Access Point:
Use this button to restart the Wireless Access Point. It is important to
Restart the Access Point any time when changing the Wireless Setting.
±
Restore Defaults:
Use this button to restore factory default configurations.
NOTE:
You will be redirected to the WL-8064ARM Wireless ADSL2/2+ Router Homepage after
the unit has successfully been restored to factory default configurations.
Page 108 / 146
102
4.6.2 TOOLS - Remote Log
Remote Log:
Using the Remote Log page, you can allow a user or users on the Internet to configure,
upgrade and check the status of your WL-8064ARM Wireless ADSL2/2+ Router.
±
Log Level:
Select the Log Level from the drop down manual. The WL-8064ARM Wireless
ADSL2/2+ Router provides the following Log Level : Panic, Alert, Critical, Error, Warning, Notice,
Info and Debug.
±
Add an IP Address:
Manually enter the logging destination IP Address then click
Add
button to
add your entry.
±
Delete:
Delete the logging destination IP Address from the drop down list.
±
Apply:
Click
Apply
to complete the setting.
±
Cancel:
Click
Cancel
to ignore all the changes.
±
To complete and save the setting, click
Save All
after clicking the
Apply
button.
Page 109 / 146
103
4.6.3 TOOLS - User Management
User Management:
The User Management page enables you to change your User Name and/or Password.
It is recommended that you change the User Name and password from the default Admin to ensure the
security of the WL-8064ARM Wireless ADSL2/2+ Router.
For security reasons, the router has its own user name and password. Also, after a period of inactivity for a
set length of time, the administrator login will automatically disconnect. When prompted, enter the router User
Name:
Admin
and the router Password:
Admin
to log in.
NOTE:
If you forget your user name and password, access to the WL-8064ARM Wireless ADSL2/2+ Router
can only be gained by resetting the unit to factory defaults. Pressing the
“Reset”
button for 10 seconds, the
LED indicators will turns OFF and ON again indicates that the Reset process is successfully done
.
±
User Name:
Enter the user specify User Name
±
Password:
Enter the user specify Password.
±
Idle Timeout:
For security, the administrator's login to the router configuration will timeout after a
period of inactivity.
±
Apply:
Click
Apply
to complete the setting.
±
Cancel:
Click
Cancel
to ignore all the changes.
±
To complete and save the setting, click
Save All
after clicking the
Apply
button.
Page 110 / 146
104
4.6.4 TOOLS - Update Gateway
Update Gateway:
Firmware is the software that controls the WL-8064ARM Wireless ADSL2/2+ Router and
also provides the user interface that is subject of this manual. The Firmware resides in the WL-8064ARM
Wireless ADSL2/2+ Router internal Flash memory; currently loaded firmware version can be found under
STATUS
Æ
Product Information
.
Note:
It is recommends that you back up your configuration before doing a firmware upgrade. After the
upgrade is complete, you may need to restore your configuration settings.
To access Firmware Updates, click on
TOOLS
Æ
Update Gateway
. The following window screen will
pop-up.
±
Select a File:
Click on the
Browse…
button to locate the Firmware or update image file from your
computer's hard drive.
±
Update Gateway:
Click the
Update Gateway
button to upgrade your WL-8064ARM Wireless
ADSL2/2+ Router. The system will be restarted automatically after the Firmware/Image is
successfully uploaded. You will need to reconnect again to configure your setup.
±
Get Configuration:
You may download your configuration file from the system by clicking
Get
Configuration
. Follow the instruction and save your configuration file in your hard drive.
19216811.live