OTE Speedport W 724V Type Ci Cosmote Router Manual PDF (Setup & Configuration Guide)

Page 146 / 152 Scroll up to view Page 141 - 145

Never separate

broadband during firmwa

malfunctioning of the Spe

Figure 8-8 Firmware upda

1. Click on

Firmware upda

2. Click on the tab

3. Click on the tab

installation.

146

e your Speedport form the power source

are update. This may cause a loss of data, w

eedport.

ate

.

and choose the storage location for the

. The router will be restarted auto

and from the

which results in

update.

omatically after

Page 147 / 152

147

8.7 System Information

Described in chapter 4.

8.8 IGMP Settings

Configure the settings for multicast protocol.

IGMP Snooping feature allows a network switch to listen in on the IGMP

conversation between hosts and routers.

As for IGMP Proxy, it can be used to implement multicast routing.

Figure 8-9 WAN Connection for IGMP Proxy

1. Click on

IGMP Settings

.

2. The hook at

IGMP Proxy

and

Snooping

should be unchecked.

3. If you decide to modify the settings (not recommended), confirm changes by

clicking the tab

. If you do not want to save changes, click on the

tab

.

Page 148 / 152

148

8.9 NTP

Configure the settings for Network Time Server. The device will contact a Network

Time Server at regular intervals and update its internal timer.

Figure 8-10 NTP

1. Click on

NTP

.

2. Enter your primary NTP server address in the entry field (preconfigured)

.

3. Enter your secondary NTP server address in the entry field (preconfigured)

.

4. Set the hook at

Enable Daylight Saving time

, if your location is currently using

Daylight Saving.

5. Once you have modified the settings, confirm the changes by clicking the tab

. If you do not want to save changes, click on the tab

.

Page 149 / 152

149

Reset to delivery status (Reset)

Your device contains private data, which could harm, once they get public. These

data may be plug recognition supplied by your provider and your personal password.

With these data strangers can surf the internet, check E-mails and carry out other

security sensitive processes at your expenses. That is why you have to carry out a

reset before you give your device for example for reparation or maintenance to third

parties.

The reset to delivery status is also necessary, if you have forgotten your personal

password and you have no more access to the configuration program. In this case

you have to completely reconfigure your device as follows:

1. Your Speedport has to be connected to the power source.

2. Use a thin pointed object to press for at least five seconds into the opening on the

backside of your Speedport labeled with

Reset

.

3. Wait 180 seconds, before disconnecting your Speedport from the power source.

Now all data are erased and replaced by the delivery status data. Now you can

unhesitatingly hand over your Speedport to someone else.

If you want to check, whether all data are erased, try out if the password has been

reset to default settings (Device password on the type label on the backside of your

Speedport). If the password has been reset, all other data have been erased as well.

Notice:

Please note that after a reset to the delivery status the WLAN name (SSID)

and the WLAN key are reset to the default settings. These are the data, which are

entered on the type label on the backside of your Speedport or in the included

WLAN device passport. If you give your Speedport to others, this information is

accessible as well for other.

Page 150 / 152

150

Troubleshooting

Within the user interface of the Speedport you can find more information for

troubleshooting. Click with the mouse on the respective entry fields or the

highlighted texts.

If your Speedport does not seem to work properly, please try to solve the problem

first with the following troubleshooting table.

General problems or problems with the local net.

Table A-1 General problems

Problem

Reason

Solution

No illuminated display

glows on the front side

of the Speedport.

The power source to the

Speedport is disconnected.

Check the used plug. Use a

device fro that of which you

are sure, that it functions.

After a firmware update

the device

malfunctions.

During a firmware update the

connections to the Speedport

were interrupted.

Reset your Speedport to

delivery status. If that does

not solve the problem,

please contact the technical

support of the OTE S.A.

A wireless connection

to the home network by

the Speedport cannot

be established.

The WLAN function on the

Speedport is deactivated.

Activate the WLAN function

on the Speedport by pressing

the key

WLAN

.

The encryption on the Speed

port does not correspond to

the encryption on the end

devices.

Set the same encryption on

the Speedport and at the end

devices.

Problems with dialing

Table A-2 Dialing problems

Problem

Reason

Solution

You cannot do calls via

internet telephony even

though your connection

Your Speedport has no

internet connection and

cannot sign in for calling.

Check if the display

Telephony

is illuminated. Check the

connection of your Speedport.

Rate

Popular OTE Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share