Netopia Motorola 3347-02 Router Manual PDF (Setup & Configuration Guide)

Page 306 / 351 Scroll up to view Page 301 - 305

306

VDSL Settings

☛

CAUTION!

These settings are for very advanced users and lab technicians. Exercise

extreme caution when modifying any of these settings.

set vdsl sys-option [ 0x00 - 0xff ]

sys-bandplan [ 0x00 - 0xff ]

psd-mask-level [ 0x00 - 0xff ]

pbo-k1_1 [ 0x00000000 - 0xffffffff ]

pbo-k1_2 [ 0x00000000 - 0xffffffff ]

pbo-k1_3 [ 0x00000000 - 0xffffffff ]

pbo-k2_1 [ 0x00000000 - 0xffffffff ]

pbo-k2_2 [ 0x00000000 - 0xffffffff ]

pbo-k2_3 [ 0x00000000 - 0xffffffff ]

line-type [ 0x00 - 0xff ]

us-max-inter-delay [ 0x00 - 0xff ]

ds-max-inter-delay [ 0x00 - 0xff ]

us-target-noise-margin [ 0x0000 - 0xffff ]

ds-target-noise-margin [ 0x0000 - 0xffff ]

min-noise-margin [ 0x0000 - 0xffff ]

port-bandplan [ 0x00 - xff ]

framing-mode [ 0x00 - 0xff ]

band-mod [ 0x00 - 0xff ]

port-option [ 0x00 - 0xff ]

power-mode [ 0x00 - 0xff ]

tx-ﬁlter [ 0x00 - 0xff ]

rx-ﬁlter [ 0x00 - 0xff ]

dying-gasp [ off | on ]

Page 307 / 351

307

CONFIG Commands

VDSL Parameter Defaults

Parameter

Default

Meaning

sys-option

0x00

VDSL system option(bit0=ntr, 1=margin, 2=ini,

3=pbo, 4=tlan, 5=pbo)

sys-bandplan

0x02

VDSL system bandplan(bp_3_998_4=2,

bp4_997_3=3, bp5_997_3=4…)

psd-mask-level

0x00

VDSL system psd mask(def=0, 1=ansim1cab,

2=ansim2cab, 3=etsim1cab, 4=etsim2cab)

pbo-k1_1

0x00

VDSL system power back-off k1_1

pbo-k1_2

0x00

VDSL system power back-off k1_2

pbo-k1_3

0x00

VDSL system power back-off k1_3

pbo-k2_1

0x00

VDSL system power back-off k2_1

pbo-k2_2

0x00

VDSL system power back-off k2_2

pbo-k2_3

0x00

VDSL system power back-off k2_3

line-type

0x81

VDSL port line type(auto=0x80, vdsl=0x81,

vdsl_etsi=0x82)

us-max-inter-delay

0x04

VDSL port upstream max inter delay

ds-max-inter-delay

0x04

VDSL port downstream max inter delay

us-target-noise-margin

0x0C

VDSL port upstream target noise margin

ds-target-noise-margin

0x0C

VDSL port downstream target noise margin

min-noise-margin

0x0A

VDSL port minimum noise margin

port-bandplan

0x02

VDSL port bandplan

framing-mode

0x90

DSL port frame mode(0-ATM; 0x80-PTM;

0x90-Auto(EFM/PTM)

band-mod

0x11

VDSL port band mod

port-option

0x0A

- Annex B

0x06

- Annex A

VDSL port portoption(bit0=I43, bit1=v43,

bit2=a43, bit3=b43)

power-mode

0x01

VDSL port power mode

tx-ﬁlter

0x02

VDSL port txPathFilterMode

rx-ﬁlter

0x02

VDSL port rxPathFilterMode

dying-gasp

off

Dying Gasp On/Off

Page 308 / 351

308

VDSL Parameters Accepted Values

Parameter

Accepted Values

sys-option

Bit[0]: NTR_DISABLE

Bit[1]: ALW_MARGIN_ADJUST.

1: the SNR margin for the optional band is reduced by up to 2.5

dB, but never below a minimum of 4 dB.

Bit[2]: SUPPORT_INI

Bit[4]: TLAN Enable

Bit[5]: PBO Weak mode Enable (Applicable only when PBO

Bit[3]=0.

Bit[6]: ADSL_SAFE_MODE Enable

Bit[7]: TLAN_SAFE_MODE Enable (Applicable only when TLAN

Enable Bit[4] is set. If TLAN_SAFE_MODE not set, line will

attempt to retrain at higher rates, but less stable line)

Page 309 / 351

309

CONFIG Commands

sys-bandplan

BP1_998_3

(0x00)

BP2_998_3

(0x01)

BP998_3B_8_5M

(0x01)

BP3_998_4

(0x02)

BP998_4B_12M

(0x02)

BP4_997_3

(0x03)

BP997_3B_7_1M

(0x03)

BP5_997_3

(0x04)

BP6_997_4

(0x05)

BP997_4B_7_1M

(0x05)

BP7_MXU_3

(0x06)

FLEX_3B_8_5M

(0x06)

BP8_MXU_2

(0x07)

BP9_998_2

(0x08)

BP10_998_2

(0x09)

BP998_2B_3_8M

(0x09)

BP11_998_2

(0x0A)

BP12_998_2

(0x0B)

BP13_MXU_3

(0x0C)

BP14_MXU_3

(0x0D)

BP15_MXU_3

(0x0E)

BP16_997_4B_4P

(0x0F)

BP17_998_138_4400

(0x10)

BP18_997_138_4400(0x11)

BP19_997_32_4400(0x12)

BP20_998_138_4400_opBand (0x15)

BP21_997_138_4400_opBand (0x16)

BP22_998_138_4400_opBand(0x16)

BP23_998_138_16000

(0x17)

BP24_998_3B_8KHZ

(0x18)

BP25_998_138_17600

(0x19)

BP26_CH1_3

(0x1A)

BP27_CH1_4

(0x1B)

VDSL Parameters Accepted Values

Parameter

Accepted Values

Page 310 / 351

310

psd-mask-level

0x00 -- default mask (old gains from before)

0x01 -- ANSI M1 CAB

0x02 -- ANSI M2 CAB

0x03 -- ETSI M1 CAB

0x04 -- ETSI M2 CAB

0x05 -- ITU-T Annex F (Japan)

0x06 - ANSI M1 Ex

0x07 - ANSI M2 Ex

0x08 -- ETSI M1 Ex

0x09 - ETSI M2 Ex

0x0A - RESERVED

0x0B - PSD_K (Korean M1 FTTCab -59dBm/Hz)

pbo-k1_1

K1 and K2 parameters allow the user more ﬂexibility in using

Upstream Power Back-Off (UPBO) on CPE modem. Changing

K1 and K2 values will affect the CPE TX PSD. Refer to VDSL

standards for exact relation between K1, K2 parameters and TX

PSD. There is an individual set of K1/K2 parameters associated

with each upstream band in the PSD: Upstream Band 0 or

Optional band, Upstream band 1, Upstream band 2 and

Upstream Band 3. Setting all K2 parameters to 0 and all K1 to a

high power level(ie low number) will essentially disable UPBO.

pbo-k1_2

pbo-k1_3

pbo-k2_1

pbo-k2_2

pbo-k2_3

line-type

VDSL_AUTO_DETECT – (0x80)

VDSL – (0x81)

VDSL_ETSI – (0x82)

us-max-inter-delay

Maximum upstream interleave delay.

Provisioned in steps of 0.5 ms. User deﬁned.

ds-max-inter-delay

Maximum downstream interleave delay.

Provisioned in steps of 0.5 ms. User deﬁned.

us-target-noise-margin

Range 0-31.0dB, increments of 0.5dB (e.g., 0 =

0dB, 1 = 0.5dB, ...)

ds-target-noise-margin

Range 0-31.0dB, increments of 0.5dB (e.g., 0 =

0dB, 1 = 0.5dB, ...)

min-noise-margin

Range 0-31.0dB, increments of 0.5dB (e.g., 0 =

0dB, 1 = 0.5dB, ...)

VDSL Parameters Accepted Values

Parameter

Accepted Values

Rate

Popular Netopia Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share