Netopia 3347-02 Qwest Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Netopia

3347-02 Qwest

Page 336 / 351 Scroll up to view Page 331 - 335

336

The Motorola Netopia® 2200 and 3300 Series complies with the following EU directives:

■

Low Voltage, 73/23/EEC

■

EMC Compatibility, 89/336/EEC, conforming to EN 55 022

Manufacturer’s Declaration of Conformance

☛

Warnings:

This is a Class B product. In a domestic environment this product may cause radio

interference, in which case the user may be required to take adequate measures. Ade-

quate measures include increasing the physical distance between this product and

other electrical devices.

Changes or modiﬁcations to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

United States.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

■

Reorient or relocate the receiving antenna.

■

Increase the separation between the equipment and receiver.

■

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

■

Consult the dealer or an experienced radio TV technician for help.

Service requirements.

In the event of equipment malfunction, all repairs should be performed by

our Company or an authorized agent. Under FCC rules, no customer is authorized to repair this

equipment. This restriction applies regardless of whether the equipment is in or our of warranty. It is

the responsibility of users requiring service to report the need for service to our Company or to one

of our authorized agents. Service can be obtained at Motorola, Inc., 6001 Shellmound Street,

Emeryville, California, 94608. Telephone: 510-597-5400.

Page 337 / 351

337

Manufacturer’s Declaration of Conformance

☛

Important

This product was tested for FCC compliance under conditions that included the use of

shielded cables and connectors between system components. Changes or modiﬁca-

tions to this product not authorized by the manufacturer could void your authority to

operate the equipment.

Canada.

This Class B digital apparatus meets all requirements of the Canadian Interference -

Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel

brouilleur du Canada.

Declaration for Canadian users

NOTICE: The Canadian Industry Canada label identiﬁes certiﬁed equipment. This

certiﬁcation means that the equipment meets certain telecommunications network

protective, operation, and safety requirements. The Department does not guarantee the

equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The equipment

must also be installed using an acceptable method of connection. In some cases, the

company’s inside wiring associated with a single line individual service may be extended

by means of a certiﬁed connector assembly (telephone extension cord). The customer

should be aware that compliance with the above conditions may not prevent degradation

of service in some situations.

Repairs to the certiﬁed equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations made by the

user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines, and internal metallic water pipe system, if present, are

connected together. This precaution may be particularly important in rural areas.

Caution

Users should not attempt to make such connections themselves, but should contact the appropriate

electric inspection authority, or electrician, as appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the

maximum number of terminals allowed to be connected to a telephone interface. The termination on

an interface may consist of any combination of devices subject only to the requirement that the sum

of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Page 338 / 351

338

Important Safety Instructions

Australian Safety Information

The following safety information is provided in conformance with Australian safety requirements:

Caution

DO NOT USE BEFORE READING THE INSTRUCTIONS: Do not connect the Ethernet ports to a carrier or

carriage service provider’s telecommunications network or facility unless: a) you have the written

consent of the network or facility manager, or b) the connection is in accordance with a connection

permit or connection rules.

Connection of the Ethernet ports may cause a hazard or damage to the telecommunication network

or facility, or persons, with consequential liability for substantial compensation.

Caution

■

The direct plug-in power supply serves as the main power disconnect; locate the direct plug-in

power supply near the product for easy access.

■

For use only with CSA Certiﬁed Class 2 power supply, rated 12VDC.

Telecommunication installation cautions

■

Never install telephone wiring during a lightning storm.

■

Never install telephone jacks in wet locations unless the jack is speciﬁcally designed for wet

locations.

■

Never touch uninsulated telephone wires or terminals unless the telephone line has been

disconnected at the network interface.

■

Use caution when installing or modifying telephone lines.

■

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

■

Do not use the telephone to report a gas leak in the vicinity of the leak.

Page 339 / 351

339

47 CFR Part 68 Information

FCC Requirements

The Federal Communications Commission (FCC) has established Rules which permit this device

to be directly connected to the telephone network. Standardized jacks are used for these

connections. This equipment should not be used on party lines or coin phones.

If this device is malfunctioning, it may also be causing harm to the telephone network; this

device should be disconnected until the source of the problem can be determined and until

repair has been made. If this is not done, the telephone company may temporarily disconnect

service.

The telephone company may make changes in its technical operations and procedures; if such

changes affect the compatibility or use of this device, the telephone company is required to give

adequate notice of the changes. You will be advised of your right to ﬁle a complaint with the

FCC.

If the telephone company requests information on what equipment is connected to their lines,

inform them of:

a. The telephone number to which this unit is connected.

b. The ringer equivalence number. [0.XB]

c. The USOC jack required. [RJ11C]

d. The FCC Registration Number. [XXXUSA-XXXXX-XX-E]

Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to

determine how many devices can be connected to your telephone line. In most areas, the sum

of the REN's of all devices on any one line should not exceed ﬁve (5.0). If too many devices are

attached, they may not ring properly.

FCC Statements

a) This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.

On the bottom of this equipment is a label that contains, among other information, a product

identiﬁer in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the

telephone company.

b) List all applicable certiﬁcation jack Universal Service Order Codes (“USOC”) for the equipment:

RJ11.

c) A plug and jack used to connect this equipment to the premises wiring and telephone network

must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A

compliant telephone cord and modular plug is provided with this product. It is designed to be

connected to a compatible modular jack that is also compliant. See installation instructions for

details.

Page 340 / 351

340

d) The REN is used to determine the number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming

call. In most but not all areas, the sum of RENs should not exceed ﬁve (5.0). To be certain of the

number of devices that may be connected to a line, as determined by the total RENs, contact the

local telephone company. For products approved after July 23, 2002, the REN for this product is part

of the product identiﬁer that has the format US:AAAEQ##TXXXX. The digits represented by ## are the

REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately

shown on the label.

e) If this equipment, the Motorola Netopia® 2200 or 3300 Series router, causes harm to the

telephone network, the telephone company will notify you in advance that temporary discontinuance

of service may be required. But if advance notice isn’t practical, the telephone company will notify

the customer as soon as possible. Also, you will be advised of your right to ﬁle a complaint with the

FCC if you believe it is necessary.

f) The telephone company may make changes in its facilities, equipment, operations or procedures

that could affect the operation of the equipment. If this happens the telephone company will provide

advance notice in order for you to make necessary modiﬁcations to maintain uninterrupted service.

g) If trouble is experienced with this equipment, the Motorola Netopia® 2200 or 3300 Series router,

for repair or warranty information, please contact:

Motorola Technical Support

510-597-5400

www.netopia.com.

If the equipment is causing harm to the telephone network, the telephone company may request that

you disconnect the equipment until the problem is resolved.

h) This equipment not intended to be repaired by the end user. In case of any problems, please refer

to the troubleshooting section of the Product User Manual before calling Motorola Technical Support.

i) Connection to party line service is subject to state tariffs. Contact the state public utility

commission, public service commission or corporation commission for information.

j) If your home has specially wired alarm equipment connected to the telephone line, ensure the

installation of this Motorola Netopia® 2200 or 3300 Series router does not disable your alarm

equipment. If you have questions about what will disable alarm equipment, consult your telephone

company or qualiﬁed installer.

RF Exposure Statement:

NOTE:

Installation of the wireless models must maintain at least 20 cm between the wireless

router and any body part of the user to be in compliance with FCC RF exposure guidelines.

Electrical Safety Advisory

Telephone companies report that electrical surges, typically lightning transients, are very destructive

to customer terminal equipment connected to AC power sources. This has been identiﬁed as a major

nationwide problem. Therefore it is advised that this equipment be connected to AC power through

the use of a surge arrestor or similar protection device.

Rate

Popular Netopia Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share