1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WPN824
    5. /
  5. 18
Page 86 / 174 Scroll up to view Page 81 - 85
Reference Manual for the RangeMax Wireless Router WPN824
8-10
Advanced Configuration of the Router
202-10072-01, March 2005
Editing or Deleting a Port Forwarding Entry
To edit or delete a Port Forwarding entry, follow these steps.
1.
In the table, select the button next to the service name.
2.
Click Edit or Delete.
Local Web and FTP Server Example
If a local computer with a private IP address of 192.168.1.33 acts as a Web and FTP server,
configure the Ports menu to forward HTTP (port 80) and FTP (port 21) to local address
192.168.1.33
In order for a remote user to access this server from the Internet, the remote user must know the IP
address that has been assigned by your ISP. If this address is 172.16.1.23, for example, an Internet
user can access your Web server by directing the browser to http://172.16.1.23. The assigned IP
address can be found in the Maintenance Status Menu, where it is shown as the WAN IP Address.
Some considerations for this application are:
•
If your account’s IP address is assigned dynamically by your ISP, the IP address may change
periodically as the DHCP lease expires.
•
If the IP address of the local computer is assigned by DHCP, it may change when the computer
is rebooted. To avoid this, you can manually configure the computer to use a fixed address.
•
Local computers must access the local server using the computers’ local LAN address
(192.168.1.33 in this example). Attempts by local computers to access the server using the
external IP address (172.16.1.23 in this example) will fail.
Multiple Computers for Half Life, KALI or Quake III Example
To set up an additional computer to play Half Life, KALI or Quake III:
1.
Click the button of an unused port in the table.
2.
Select the game again from the Services/Games list.
3.
Change the beginning port number in the Start Port box.
For these games, use the supplied number in the default listing and add +1 for each additional
computer. For example, if you've already configured one computer to play Hexen II (using
port 26900), the second computer's port number would be 26901, and the third computer
would be 26902.
Page 87 / 174
Reference Manual for the RangeMax Wireless Router WPN824
Advanced Configuration of the Router
8-11
202-10072-01, March 2005
4.
Type the same port number in the End Port box that you typed in the Start Port box.
5.
Type the IP address of the additional computer in the Server IP Address box.
6.
Click Apply.
Some online games and videoconferencing applications are incompatible with NAT. The WPN824
router is programmed to recognize some of these applications and to work properly with them, but
there are other applications that may not function well. In some cases, one local computer can run
the application properly if that computer’s IP address is entered as the default in the PORTS Menu.
If one local computer acts as a game or videoconferencing host, enter its IP address as the default.
Configuring the WAN Setup Options
The WAN Setup options let you configure a DMZ server, change the MTU size and enable the
wireless router to respond to a Ping on the WAN port. These options are discussed below.
Figure 8-8:
WAN Setup menu.
Connect Automatically, as Required
Normally, this option should be checked to enable it. An Internet connection will be made
automatically after each timeout, whenever Internet-bound traffic is detected. This provides
connection on demand and is potentially cost-saving in places in Europe for example where
Internet services charge by the minute.
Page 88 / 174
Reference Manual for the RangeMax Wireless Router WPN824
8-12
Advanced Configuration of the Router
202-10072-01, March 2005
If disabled, you must connect manually, using the “Connection Status” button on the Router Status
screen. This manual connection will stay up all the time without time outs.
Disabling the SPI Firewall
The SPI (Stateful Inspection) Firewall protects your LAN against Denial of Service attacks. This
should only be disabled in special circumstances.
Setting Up a Default DMZ Server
The default DMZ server feature is helpful when using some online games and videoconferencing
applications that are incompatible with NAT. The router is programmed to recognize some of these
applications and to work properly with them, but there are other applications that may not function
well. In some cases, one local computer can run the application properly if that computer’s IP
address is entered as the default DMZ server.
Incoming traffic from the Internet is normally discarded by the router unless the traffic is a
response to one of your local computers or a service that you have configured in the Ports menu.
Instead of discarding this traffic, you can have it forwarded to one computer on your network. This
computer is called the Default DMZ Server.
The WAN Setup menu, shown below lets you configure a Default DMZ Server.
To assign a computer or server to be a Default DMZ server, follow these steps:
1.
Click WAN Setup link on the Advanced section of the main menu.
2.
Type the IP address for that server. To remove the default DMZ server, replace the IP address
numbers with all zeros.
3.
Click Apply.
Responding to Ping on Internet WAN Port
If you want the router to respond to a 'ping' from the Internet, click the ‘Respond to Ping on
Internet WAN Port’ check box. This should only be used as a diagnostic tool, since it allows your
router to be discovered. Don't check this box unless you have a specific reason to do so.
Note:
DMZ servers pose a security risk. A computer designated as the default DMZ
server loses much of the protection of the firewall, and is exposed to exploits from the
Internet. If compromised, the DMZ server can be used to attack your network.
Page 89 / 174
Reference Manual for the RangeMax Wireless Router WPN824
Advanced Configuration of the Router
8-13
202-10072-01, March 2005
Setting the MTU Size
The normal MTU (Maximum Transmit Unit) value for most Ethernet networks is 1500 Bytes,
1492 Bytes for PPPoE connections, or 1436 for PPTP connections. For some ISPs you may need to
reduce the MTU. But this is rarely required, and should not be done unless you are sure it is
necessary for your ISP connection.
Any packets sent through the router that are larger than the configured MTU size will be
repackaged into smaller packets to meet the MTU requirement. To change the MTU size:
1.
Under MTU Size, enter a new size between 64 and 1500.
2.
Click Apply to save the new configuration.
Using the LAN IP Setup Options
Another feature category under the Advanced heading is LAN IP Setup. This menu allows
configuration of LAN IP services such as DHCP and RIP. From the Main Menu of the browser
interface, under Advanced, click on LAN IP Setup to view the LAN IP Setup menu, shown below.
Figure 8-9:
LAN IP Setup Menu
Page 90 / 174
Reference Manual for the RangeMax Wireless Router WPN824
8-14
Advanced Configuration of the Router
202-10072-01, March 2005
Configuring LAN TCP/IP Setup Parameters
The router is shipped preconfigured to use private IP addresses on the LAN side, and to act.as a
DHCP server. The router’s default LAN IP configuration is:
•
LAN IP addresses—192.168.1.1
•
Subnet mask—255.255.255.0
These addresses are part of the IETF-designated private address range for use in private networks,
and should be suitable in most applications. If your network has a requirement to use a different IP
addressing scheme, you can make those changes in this menu.
The LAN IP parameters are:
•
IP Address
This is the LAN IP address of the router.
•
IP Subnet Mask
This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask
allows a device to know which other addresses are local to it, and which must be reached
through a gateway or router.
•
RIP Direction
RIP (Router Information Protocol) allows a router to exchange routing information with other
routers. The RIP Direction selection controls how the router sends and receives RIP packets.
Both is the default.
—
When set to Both or Out Only, the router will broadcast its routing table periodically.
—
When set to Both or In Only, it will incorporate the RIP information that it receives.
—
When set to None, it will not send any RIP packets and will ignore any RIP packets
received.
•
RIP Version
This controls the format and the broadcasting method of the RIP packets that the router sends.
(It recognizes both formats when receiving.) By default, this is set for RIP-1.
—
RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you
have an unusual network setup.
—
RIP-2 carries more information. RIP-2B uses subnet broadcasting.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top