1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WNR1000v2
    5. /
  5. 10
Page 46 / 122 Scroll up to view Page 41 - 45
Wireless-N 150 Router WNR1000v2 User Manual
Safeguarding Your Network
2-19
v1.0, November 2009
2.
In the Advanced Wireless Settings screen, click
Setup Access List
to display the Wireless
Card Access List.
3.
Click
Add
to add a wireless device to the wireless access control list. The Wireless Card
Access Setup screen opens and displays a list of currently active wireless cards and their
Ethernet MAC addresses.
4.
If the computer you want appears in the Available Wireless Cards list, you can select the radio
button of that computer to capture its MAC address; otherwise, you can manually enter a name
and the MAC address of the authorized computer. You can usually find the MAC address on
the bottom of the wireless device.
Figure 2-11
Figure 2-12
Tip:
You can copy and paste the MAC addresses from the router’s Attached Devices
screen into the MAC Address field of this screen. To do this, configure each
wireless computer to obtain a wireless link to the router. The computer should
then appear in the Attached Devices screen.
Page 47 / 122
Wireless-N 150 Router WNR1000v2 User Manual
Safeguarding Your Network
2-20
v1.0, November 2009
5.
Click
Add
to add this wireless device to the Wireless Card Access List. The screen changes
back to the list screen.
6.
Repeat
step 3
through
step 5
for each additional device you want to add to the list.
7.
Select the
Turn Access Control On
check box.
8.
Click
Apply
to save your Wireless Card Access List settings.
Now, only devices on this list can wirelessly connect to the WNR1000v2 router.
Changing the Administrator Password
The default password for the router’s Web Configuration Manager is
password
. NETGEAR
recommends that you change this password to a more secure password.
Note:
When configuring the router from a wireless computer whose MAC address is
not in the Trusted PC list, if you select
Turn Access Control On
, you lose
your wireless connection when you click
Apply
. You must then access the
wireless router from a wired computer or from a wireless computer that is on
the access control list to make any further changes.
Warning:
MAC address filtering adds an obstacle against unwanted access to your
network by the general public. However, because your trusted MAC
addresses appear in your wireless transmissions, an intruder can read them
and impersonate them. Do not rely on MAC address filtering alone to
secure your network.
Tip:
Before changing the router password, back up your configuration settings with the
default password of
password
. If you save the settings with a new password, and
then you later forget the new password, you will have to reset the router back to the
factory defaults, and log in using the default password of
password
. This means you
will have to re-enter all the router configuration settings. For information about how
to back up your settings, see
“Backing Up and Restoring the Configuration” on
page 6-8
.
Page 48 / 122
Wireless-N 150 Router WNR1000v2 User Manual
Safeguarding Your Network
2-21
v1.0, November 2009
To change the administrator password:
1.
On the main menu, under Maintenance, select
Set Password
to display the Set Password
screen.
2.
To change the password, first enter the old password, then enter the new password twice.
3.
Click
Apply
.
Backing Up Your Configuration
The configuration settings of the WNR1000v2 router are stored within the router in a
configuration file. You can back up (save) this file and retrieve it later. NETGEAR recommends
that you save your configuration file after you complete the configuration. If the router fails or
becomes corrupted, or an administrator password is lost, you can easily re-create your
configuration by restoring the configuration file.
For instructions on saving and restoring your configuration file, see
“Managing the Configuration
File” on page 6-7
.
Figure 2-13
Tip:
Before saving your configuration file, change the administrator password to the
default,
password
. Then change it again after you have saved the configuration file.
If you save the file with a new password, and then you later forget the new
password, you will have to reset the router back to the factory defaults and log in
using the default password of
password
. This means you will have to re-enter all the
router configuration settings.
Page 49 / 122
Wireless-N 150 Router WNR1000v2 User Manual
Safeguarding Your Network
2-22
v1.0, November 2009
Understanding Your Firewall
Your Wireless-N 150 Router Model WNR1000v2
contains a true firewall to protect your network
from attacks and intrusions. A firewall is a device that protects one network from another while
allowing communication between the two. Using a process called Stateful Packet Inspection, the
firewall analyzes all inbound and outbound traffic to determine whether or not it will be allowed to
pass through.
By default, the firewall allows any outbound traffic and prohibits any inbound traffic except for
responses to your outbound traffic. However, you can modify the firewall’s rules to achieve the
following behavior:
•
Blocking sites
. Block access from your network to certain Web locations based on Web
addresses and Web address keywords. This feature is described in
“Blocking Access to
Internet Sites” on page 3-1
.
•
Blocking services
. Block the use of certain Internet services by specific computers on your
network. This feature is described in
“Blocking Access to Internet Services” on page 3-3
.
•
Scheduled blocking
. Block sites and services according to a daily schedule. This feature is
described in
“Scheduling Blocking” on page 3-5
.
•
Allow inbound access to your server
. To allow inbound access to resources on your local
network (for example, a Web server or remote desktop program), you can open the needed
services by configuring port forwarding as described in
“Allowing Inbound Connections to
Your Network” on page 5-1
.
•
Allow certain games and applications to function correctly
. Some games and applications
need to allow additional inbound traffic in order to function. Port triggering can dynamically
allow additional service connections, as described in
“Configuring Port Triggering” on
page 5-9
. Another feature to solve application conflicts with the firewall is Universal Plug and
Play (UPnP), described in
“Using Universal Plug and Play” on page 5-12
.
Page 50 / 122
3-1
v1.0, November 2009
Chapter 3
Restricting Access From Your Network
This chapter describes how to use the content filtering and reporting features of the Wireless-N
150 Router Model WNR1000v2
to protect your network.
This chapter includes the following sections:
•
“Content Filtering Overview
”
•
“Blocking Access to Internet Sites
”
•
“Blocking Access to Internet Services” on page 3-3
•
“Scheduling Blocking” on page 3-5
•
“Viewing Logs of Web Access or Attempted Web Access” on page 3-6
•
“Configuring E-mail Alert and Web Access Log Notifications” on page 3-7
•
“Setting the Time Zone” on page 3-8
Content Filtering Overview
The Wireless-N 150 Router Model WNR1000v2
provides you with Web content filtering options,
plus browser activity reporting and instant alerts through e-mail. Parents and network
administrators can establish restricted access policies based on time of day, Web addresses, and
Web address keywords. You can also block Internet access by applications and services, such as
chat rooms or games.
Blocking Access to Internet Sites
The WNR1000v2 router allows you to restrict access based on Web addresses and Web address
keywords. Up to 255 entries are supported in the Keyword list.
Keyword application examples:
•
If the keyword
XXX
is specified, the URL www.zzzyyqq.com/xxx.html is blocked.
•
If the keyword
.com
is specified, only websites with other domain suffixes (such as .edu, .org,
or .gov) can be viewed.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top