1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WNDR3300
    5. /
  5. 23
Page 111 / 134 Scroll up to view Page 106 - 110
NETGEAR RangeMax™ Dual Band Wireless-N Router WNDR3300 Reference Manual
Troubleshooting
7-5
v1.0, January 2008
•
Make sure that you are using the correct login information. The factory default login name is
admin
, and the password is
password
. Make sure that Caps Lock is off when entering this
information.
If the router does not save changes you have made in the Web Configuration Interface, check the
following:
•
When entering configuration settings, be sure to click
Apply
before moving to another screen
or tab, or your changes could be lost.
•
Click
Refresh
or
Reload
in the Web browser. The changes might have occurred, but the Web
browser might be caching the old configuration.
Troubleshooting the Internet Connection
If you can access your router but you are unable to access the Internet, you should first determine
whether the router is able to obtain an IP address from your Internet Service Provider (ISP). Unless
your ISP provides a fixed IP address, your router must request an IP address from the ISP. You can
determine whether the request was successful using the Web Configuration Manager.
To check the WAN IP address:
1.
Start your browser, and select an external site such as
.
2.
Access the main menu of the router’s configuration at
.
3.
Under Maintenance, select
Router Status
.
4.
Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router has not
obtained an IP address from your ISP.
If your router is unable to obtain an IP address from the ISP, you might need to force your cable or
DSL modem to recognize your new router by restarting your network, as described in
“Be sure to
restart your network in this sequence. ” on page 7-1
.
If your router is still unable to obtain an IP address from the ISP, the problem might be one of the
following:
•
Your ISP might require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of login.
•
If your ISP requires a login, the login name and password might be set incorrectly.
•
Your ISP might check for your computer’s host name.
Assign the computer host name of your ISP account as the account name in the Basic Settings
screen.
Page 112 / 134
NETGEAR RangeMax™ Dual Band Wireless-N Router WNDR3300 Reference Manual
7-6
Troubleshooting
v1.0, January 2008
•
Your ISP allows only one Ethernet MAC address to connect to Internet and might check for
your computer’s MAC address. In this case, do one of the following:
–
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address.
–
Configure your router to spoof your computer’s MAC address. This procedure is
explained in
“Configuring Your Internet Connection Using the Smart Setup Wizard” on
page 1-5
.
If your router can obtain an IP address, but your computer is unable to load any Web pages from
the Internet:
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically, your ISP provides the addresses of one or two DNS servers
for your use. If you entered a DNS address during the router’s configuration, reboot your
computer, and verify the DNS address as described in the online document you can access
from
“Preparing Your Network” in Appendix B
. You can also configure your computer
manually with DNS addresses, as explained in your operating system documentation
.
•
Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer, and
verify the gateway address as described in the online document you can access from
“Preparing Your Network” in Appendix B
.
•
You might be running login software that is no longer needed.
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no longer
need to run that software after installing your router. You might need to go to Internet Explorer
and select
Tools > Internet Options
, click the Connections tab, and select
Never dial a
connection
.
Troubleshooting a Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to the
designated device. The device then responds with an echo reply. You can easily troubleshoot a
network by using the ping utility in your computer or workstation.
Page 113 / 134
NETGEAR RangeMax™ Dual Band Wireless-N Router WNDR3300 Reference Manual
Troubleshooting
7-7
v1.0, January 2008
Testing the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.
To ping the router from a running Windows PC:
1.
From the Windows toolbar, click the Start button, and then select
Run
.
2.
In the field provided, type
ping
followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3.
Click
OK
.
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
–
For a wired connection, make sure the numbered Ethernet port light is on for the port
to which you are connected. If the light is off, follow the instructions in
“The Internet
or Ethernet port lights are not on.” on page 7-3
.
–
Check that the corresponding Link lights are on for your network interface card. If
your router and computer are connected to a separate Ethernet switch, make sure the
Link lights are on for the switch ports that are connected to your computer and router.
•
Wrong network configuration
–
Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your computer.
–
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.
Page 114 / 134
NETGEAR RangeMax™ Dual Band Wireless-N Router WNDR3300 Reference Manual
7-8
Troubleshooting
v1.0, January 2008
Testing the Path from Your Computer to a Remote Device
After verifying that the LAN path works correctly, test the path from your computer to a remote
device.
1.
From the Windows toolbar, click the Start button, and then select
Run
.
2.
In the Windows Run window, type:
ping -n 10
<
IP address
>
where <
IP address
> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies like those shown in the previous section are displayed.
If you do not receive replies:
•
Check that your computer has the IP address of your router listed as the default gateway. If the
IP configuration of your computer is assigned by DHCP, this information is not visible in your
computer’s Network Control Panel. Verify that the IP address of the router is listed as the
default gateway as described in the online document you can access from
“Preparing Your
Network” in Appendix B
.
•
Check to see that the network address of your computer (the portion of the IP address specified
by the subnet mask) is different from the network address of the remote device.
•
Check that your cable or DSL modem is connected and functioning.
•
If your ISP assigned a host name to your computer, enter that host name as the account name
in the Basic Settings screen.
•
Your ISP could be rejecting the Ethernet MAC addresses of all but one of your computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of your
broadband modem, but some ISPs additionally restrict access to the MAC address of a single
computer connected to that modem. If this is the case, you must configure your router to
“clone” or “spoof” the MAC address from the authorized computer. For more information, see
“Configuring Your Internet Connection Using the Smart Setup Wizard” on page 1-5
.
Problems with Date and Time
Under Content Filtering in the main menu, select
E-mail
to display a screen that shows the current
date and time of day. The WNDR3300 router uses the Network Time Protocol (NTP) to obtain the
current time from one of several network time servers on the Internet. Each entry in the log is
stamped with the date and time of day. Problems with the date and time function can include the
following:
Page 115 / 134
NETGEAR RangeMax™ Dual Band Wireless-N Router WNDR3300 Reference Manual
Troubleshooting
7-9
v1.0, January 2008
•
Date shown is January 1, 2000.
Cause: The router has not yet successfully reached a Network Time Server. Check that your
Internet access is configured correctly. If you have just completed configuring the router, wait
at least 5 minutes, and check the date and time again.
•
Time is off by one hour.
Cause: The router does not adjust for daylight savings time. In the E-mail screen, select the
Adjust for Daylight Savings Time
check box.
Solving Wireless Connection Problems
The first steps in solving wireless connection problems are these:
1.
Using your wireless card’s setup utility program, make sure that your wireless card can find
your wireless router.
2.
Configure and test with the simplest wireless connection possible, and then add security.
The topics in this section describe these steps.
Using Your Wireless Card Setup Program
When you install a NETGEAR wireless card in your computer, a Smart Wizard utility program is
installed that can provide helpful information about your wireless network. You can find this
program in your Windows Program menu or as an icon in your system tray. Other wireless card
manufacturers might include a similar program.
If you have no specific wireless card setup program installed, you can use the basic setup utility in
Windows by following these steps:
1.
Open the Windows Control Panel, and double-click
Network Connections
.
2.
In the LAN section, double-click
Wireless Network Connection
.
Use the setup program to scan for available wireless networks. Look for a network name (SSID) of
NETGEAR or your custom SSID if you have changed it. If your wireless network does not appear,
check these conditions:
•
Is your router’s wireless radio enabled? See
“Viewing Advanced Wireless Settings” on
page 2-11
.
•
Is your router’s SSID broadcast enabled? See
“Viewing Advanced Wireless Settings” on
page 2-11
.

Rate

3.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top