NETGEAR WGR614v5 Router Manual PDF (Setup & Configuration Guide)

Page 116 / 172 Scroll up to view Page 111 - 115

Reference Manual for the 54 Mbps Wireless Router WGR614 v5

B-16

Network, Routing, Firewall, and Basics

July 2004 202-10036-01

Page 117 / 172

Preparing Your Network

C-1

July 2004 202-10036-01

Appendix C

Preparing Your Network

This appendix describes how to prepare your network to connect to the Internet through the 54

Mbps Wireless Router WGR614 v5 and how to verify the readiness of broadband Internet service

from an Internet service provider (ISP).

What You Need To Use a Router with a Broadband Modem

You need to prepare these three things before you begin:

Cabling and Computer Hardware

To use the WGR614 v5 router on your network, each computer must have an 802.11g or 802.11b

wireless adapter or an installed Ethernet Network Interface Card (NIC) and an Ethernet cable. If

the computer will connect to your network using an Ethernet NIC at 100 Mbps, you must use a

Category 5 (Cat 5) cable such as the one provided with your router. For an explanation of Ethernet

cabling, see

“Ethernet Cabling“ on page B-11

. The cable or DSL broadband modem must provide

a standard 10 Mbps (10BASE-T) or 100 Mbps (100BASE-Tx) Ethernet interface.

Computer Network Configuration Requirements

The WGR614 v5 includes a built-in Web Configuration Manager. To access the configuration

menus on the WGR614 v5, your must use a Java-enabled Web browser program which supports

HTTP uploads such as Microsoft Internet Explorer or Netscape Navigator. Use Internet Explorer

or Netscape Navigator 4.0 or above.

Note:

If an ISP technician configured your computer during the installation of a

broadband modem, or if you configured it using instructions provided by your ISP, you

may need to copy the current configuration information for use in the configuration of

your firewall. Write down this information before reconfiguring your computers. Refer

to

“Obtaining ISP Configuration Information for Windows Computers

” on

page C-21

or

“Obtaining ISP Configuration Information for Macintosh Computers

” on

page C-22

for

further information.

Page 118 / 172

Reference Manual for the 54 Mbps Wireless Router WGR614 v5

C-2

Preparing Your Network

July 2004 202-10036-01

For the initial setup of your router, you will need to connect a computer to the router. This

computer has to be set to automatically get its TCP/IP configuration from the router via DHCP.

Note:

For help with DHCP configuration, please use the Windows TCP/IP Configuration

Tutorials on the

NETGEAR 54 Mbps Wireless Router WGR614 v5 Resource CD (230-10091-01)

,

or in this appendix.

Internet Configuration Requirements

Depending on how your Internet service set up your account, you may need one or more of these

configuration parameters to connect your router to the Internet:

•

Host and Domain Names

•

ISP Login Name and Password

•

ISP Domain Name Server (DNS) Addresses

•

Fixed IP Address which is also known as Static IP Address

Where Do I Get the Internet Configuration Parameters?

There are several ways you can gather the required Internet connection information.

•

Your Internet service provides all the information needed to connect to the Internet. If you

cannot locate this information, you can ask your Internet service to provide it or you can try

one of the options below.

•

If you have a computer already connected using the Internet, you can gather the configuration

information from that computer.

—

For Windows 95/98/ME, open the Network control panel, select the TCP/IP entry for the

Ethernet adapter, and click Properties. Record all the settings for each tab page.

—

For Windows 2000/XP, open the Local Area Network Connection, select the TCP/IP entry

for the Ethernet adapter, and click Properties. Record all the settings for each tab page.

—

For Macintosh computers, record the settings in the TCP/IP or Network control panel.

•

You may also refer to the

NETGEAR 54 Mbps Wireless Router WGR614 v5 Resource CD

(230-10091-01)

for the NETGEAR Router ISP Guide which provides Internet connection

information for many ISPs.

Once you locate your Internet configuration parameters, you may want to record them on the page

below.

Page 119 / 172

Reference Manual for the 54 Mbps Wireless Router WGR614 v5

Preparing Your Network

C-3

July 2004 202-10036-01

Record Your Internet Connection Information

Print this page. Fill in the configuration parameters from your Internet Service Provider (ISP).

ISP Login Name:

The login name and password are case sensitive and must be entered exactly as

given by your ISP. Some ISPs use your full e-mail address as the login name. The Service Name is

not required by all ISPs. If you connect using a login name and password, enter the following:

Login Name: ______________________________

Password: ____________________________

Service Name: _____________________________

Fixed or Static IP Address:

If you have a static IP address, record the following information. For

example, 169.254.141.148 could be a valid IP address.

Fixed or Static Internet IP Address: ______

______

Gateway IP Address: ______

______

Subnet Mask: ______

______

ISP DNS Server Addresses:

If you were given DNS server addresses, fill in the following:

Primary DNS Server IP Address: ______

______

Secondary DNS Server IP Address: ______

______

Host and Domain Names:

Some ISPs use a specific host or domain name like

CCA7324-A

or

home

. If you haven’t been given host or domain names, you can use the following examples as a

guide:

•

If your main e-mail account with your ISP is

[email protected]

, then use

aaa

as your host name.

Your ISP might call this your account, user, host, computer, or system name.

•

If your ISP’s mail server is

mail.xxx.yyy.com

, then use

xxx.yyy.com

as the domain name.

ISP Host Name: _________________________

ISP Domain Name: _______________________

For Wireless Access:

See the configuration worksheet at

“Information to Gather Before Changing

Basic Wireless Settings“ on page 4-6

.

Preparing Your Computers for TCP/IP Networking

Computers access the Internet using a protocol called TCP/IP (Transmission Control Protocol/

Internet Protocol). Each computer on your network must have TCP/IP installed and selected as its

networking protocol. If a Network Interface Card (NIC) is already installed in your computer, then

TCP/IP is probably already installed as well.

Page 120 / 172

Reference Manual for the 54 Mbps Wireless Router WGR614 v5

C-4

Preparing Your Network

July 2004 202-10036-01

Most operating systems include the software components you need for networking with TCP/IP:

•

Windows

®

95 or later includes the software components for establishing a TCP/IP network.

•

Windows 3.1 does not include a TCP/IP component. You need to purchase a third-party TCP/

IP application package such as NetManage Chameleon.

•

Macintosh Operating System 7 or later includes the software components for establishing a

TCP/IP network.

•

All versions of UNIX or Linux include TCP/IP components. Follow the instructions provided

with your operating system or networking software to install TCP/IP on your computer.

In your IP network, each computer and the firewall must be assigned a unique IP addresses. Each

computer must also have certain other IP configuration information such as a subnet mask

(netmask), a domain name server (DNS) address, and a default gateway address. In most cases,

you should install TCP/IP so that the computer obtains its specific network configuration

information automatically from a DHCP server during bootup. For a detailed explanation of the

meaning and purpose of these configuration items, refer to “

Appendix B, “Network, Routing,

Firewall, and Basics

.”

The WGR614 v5 router is shipped preconfigured as a DHCP server. The firewall assigns the

following TCP/IP configuration information automatically when the PCs are rebooted:

•

PC or workstation IP addresses—192.168.0.2 through 192.168.0.254

•

Subnet mask—255.255.255.0

•

Gateway address (the firewall)—192.168.0.1

These addresses are part of the IETF-designated private address range for use in private networks.

Configuring Windows 95, 98, and Me for TCP/IP Networking

As part of the PC preparation process, you need to manually install and configure TCP/IP on each

networked PC. Before starting, locate your Windows CD; you may need to insert it during the

TCP/IP installation process.

Install or Verify Windows Networking Components

To install or verify the necessary components for IP networking:

1.

On the Windows taskbar, click the Start button, point to Settings, and then click Control Panel.

Rate

Popular NETGEAR Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share