Page 131 / 172
Scroll up to view Page 126 - 130
Reference Manual for the 54 Mbps Wireless Router WGR614 v5
Preparing Your Network
C-15
July 2004 202-10036-01
DHCP Configuration of TCP/IP in Windows NT4
Once you have installed the network card, you need to configure the TCP/IP environment for
Windows NT 4.0. Follow this procedure to configure TCP/IP with DHCP in Windows NT 4.0.
• Choose
Settings
from the Start Menu, and then select
Control Panel
.
This will display Control Panel window.
• Double-click the
Network
icon in the
Control Panel window.
The Network panel will display.
• Select the
Protocols
tab to continue.
Page 132 / 172
Reference Manual for the 54 Mbps Wireless Router WGR614 v5
C-16
Preparing Your Network
July 2004 202-10036-01
• Highlight the
TCP/IP Protocol
in the
Network Protocols
box, and click on the
Properties
button.
Page 133 / 172
Reference Manual for the 54 Mbps Wireless Router WGR614 v5
Preparing Your Network
C-17
July 2004 202-10036-01
Verifying TCP/IP Properties for Windows XP, 2000, and NT4
To check your PC’s TCP/IP configuration:
1.
On the Windows taskbar, click the Start button, and then click Run.
The Run window opens.
2.
Type
cmd
and then click OK.
A command window opens
3.
Type
ipconfig /all
Your IP Configuration information will be listed, and should match the values below if you are
using the default TCP/IP settings that NETGEAR recommends for connecting through a
router or gateway:
•
The IP address is between 192.168.0.2 and 192.168.0.254
•
The subnet mask is 255.255.255.0
• The
TCP/IP Properties
dialog box now
displays.
• Click the
IP Address
tab
.
•
Select the radio button marked
Obtain an IP
address from a DHCP server.
• Click
OK
.
This completes the configuration
of TCP/IP in Windows NT.
Restart the PC.
Repeat these steps for each PC with this version
of Windows on your network.
Page 134 / 172
Reference Manual for the 54 Mbps Wireless Router WGR614 v5
C-18
Preparing Your Network
July 2004 202-10036-01
•
4.
Type
exit
Configuring the Macintosh for TCP/IP Networking
Beginning with Macintosh Operating System 7, TCP/IP is already installed on the Macintosh. On
each networked Macintosh, you will need to configure TCP/IP to use DHCP.
MacOS 8.6 or 9.x
1.
From the Apple menu, select Control Panels, then TCP/IP.
The TCP/IP Control Panel opens:
2.
From the “Connect via” box, select your Macintosh’s Ethernet interface.
3.
From the “Configure” box, select Using DHCP Server.
You can leave the DHCP Client ID box empty.
4.
Close the TCP/IP Control Panel.
5.
Repeat this for each Macintosh on your network.
MacOS X
1.
From the Apple menu, choose System Preferences, then Network.
Page 135 / 172
Reference Manual for the 54 Mbps Wireless Router WGR614 v5
Preparing Your Network
C-19
July 2004 202-10036-01
2.
If not already selected, select Built-in Ethernet in the Configure list.
3.
If not already selected, Select Using DHCP in the TCP/IP tab.
4.
Click Save.
Verifying TCP/IP Properties for Macintosh Computers
After your Macintosh is configured and has rebooted, you can check the TCP/IP configuration by
returning to the TCP/IP Control Panel. From the Apple menu, select Control Panels, then TCP/IP.
The panel is updated to show your settings, which should match the values below if you are using
the default TCP/IP settings that NETGEAR recommends:
•
The IP Address is between 192.168.0.2 and 192.168.0.254
•
The Subnet mask is 255.255.255.0
•
If you do not see these values, you may need to restart your Macintosh or you may need to switch
the “Configure” setting to a different option, then back again to “Using DHCP Server”.
19216811.live