1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. WAG102
    5. /
  5. 12
Page 56 / 82 Scroll up to view Page 51 - 55
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
4-2
Management
v1.0, September 2005
–
Manager IP Address:
Enter the IP address of the SNMP manager. If this is set to
255.255.255.255,
–
IP address to Receive Traps:
The IP address of the SNMP manager to receive traps sent
from the wireless access point. The default is 0.0.0.0.
Using Syslog and Activity Log Information
The Information contains the Activity Log link you can use for setting up a syslog server and
viewing activity log information.
1.
From the main menu of the browser interface, under the Information heading, click the
Activity Log link to view the list, shown below.
The Activity Log Window displays the Access Point system activity.
2.
To update the Activity Log display, click Refresh. To save the log contents into a file on your
PC, click Save As and save the file to a disk drive.
Figure 4-2
Page 57 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
Management
4-3
v1.0, September 2005
3.
Enable the SysLog option if you have a SysLog server on your LAN. If enabled, you must
enter the IP address of your SysLog server and the port number your SysLog server is
configured to use.
•
SysLog Server IP address: The access point will send all the SysLog to the specified IP
address if SysLog option is enabled. Default: 0.0.0.0
•
Port: The port number configured in the SysLog server on your LAN. Default: 514
Viewing General and Statistical Information
General Information
The General information screen provides a summary of the current WAG102 configuration
settings. From the main Menu of the browser interface, click General to view the System Status
screen, shown below.
Figure 4-3
Page 58 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
4-4
Management
v1.0, September 2005
This screen shows the following parameters:
Table 4-1. General Information Fields
Field
Description
Access Point Information
Access Point Name
(NetBIOS name)
The default name may be changed if desired.
MAC Address
Displays the Media Access Control address (MAC address) of the wireless
access point’s Ethernet port.
Country/Region
Displays the domain or region for which the wireless access point is
licensed for use. It may not be legal to operate this wireless access point in
a region other than one of those identified in this field.
Firmware Version
The version of the firmware currently installed.
Current IP Settings
IP Address
The IP address of the wireless access point.
Subnet Mask
The subnet mask for the wireless access point.
Default Gateway
The default gateway for the wireless access point communication.
DHCP Client
Enabled indicates that the current IP address was obtained from a DHCP
server on your network. Disabled indicated a static IP configuration.
Current Wireless Settings 11a
Access Point Mode
Identifies the operating mode of the WAG102: Access Point, Point-to-point
bridge, Point to Multi-point bridge or Repeater.
Operating Mode
Identifies the 802.11 operating mode of the WAG102.
Wireless Network Name
(SSID)
Displays the wireless network name (SSID) being used by the wireless port
of the wireless access point. The default is NETGEAR_11a.
Channel/Frequency
Identifies the channel the wireless port is using. By default, the channel is
set automatically. To manually set the channel, see
“Wireless
Communications:” in Appendix B
.
WEP/WPA
WEP/WPA setting.
Page 59 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
Management
4-5
v1.0, September 2005
Current Wireless Settings 11b/g
Access Point Mode
Identifies the operating mode of the WAG102: Access Point, Point-to-point
bridge, Point to Multi-point bridge, or Repeater.
Operating Mode
Identifies the 802.11 operating mode of the WAG102.
Wireless Network Name
(SSID)
Displays the wireless network name (SSID) being used by the wireless port
of the wireless access point. The default is NETGEAR_11g.
Channel/Frequency
Identifies the channel the wireless port is using. 11 is the default channel
setting. By default, the channel is set automatically. To manually set the
channel, see
“Wireless Communications:” in Appendix B
.
WEP/WPA
WEP/WPA setting.
Table 4-1. General Information Fields
Field
Description
Page 60 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
4-6
Management
v1.0, September 2005
Statistics
The Information - Statistics screen provides various LAN and WLAN statistics.
Figure 4-4
Table 4-1. Statistics Fields
Field
Description
Wired Ethernet
Received/Transmitted
Packets
The number of packets sent since the WAG102 was restarted.
Bytes
The number of bytes sent since the WAG102 was restarted.
Wireless 11a
Received/Transmitted
Unicast Packets
The Unicast packets sent since the WAG102 was restarted.
Broadcast Packets
The Broadcast packets sent since the WAG102 was restarted.
Multicast Packets
The Multicast packets sent since the WAG102 was restarted.
Total Packets
The Wireless packets sent since the WAG102 was restarted.
Total Bytes
The Wireless bytes sent since the WAG102 was restarted.

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top