Page 51 / 82
Scroll up to view Page 46 - 50
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
Basic Installation and Configuration
3-29
v1.0, September 2005
6.
Click
WEP/WPA Settings
in the Security menu.
7.
Choose
WPA with Radius
,
WPA2 with Radius
, or
WPA and WPA2 with Radius
from the
list.
8.
Click
Apply
to save your settings.
Figure 3-14
WEP/WPA Settings 11a menu
WEP/WPA Settings 11b/g menu
Page 52 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
3-30
Basic Installation and Configuration
v1.0, September 2005
How to Configure WPA-PSK and/or WPA2-PSK
To configure WPA-PSK, follow these steps:
1.
Log in at the default LAN address of
with the default user name of
admin
and default password of
password
, or using whatever LAN address and password you
have set up.
2.
Click the WEP/WPA Settings link in the main menu of the WAG102.
3.
Choose
WPA-PSK
,
WPA2-PSK
, or
WPA-PSK and WPA2-PSK
from the list.
4.
Enter the pre-shared key passphrase.
Note:
Not all wireless adapters support WPA. Furthermore, client software is required on
the client. Windows XP and Windows 2000 with Service Pack 3 or above do
include the client software that supports WPA. Nevertheless, the wireless adapter
hardware and driver must also support WPA. Consult the product document for
your wireless adapter and WPA client software for instructions on configuring
WPA settings.
Figure 3-15
WEP/WPA Settings 11a menu
WEP/WPA Settings 11b/g menu
Page 53 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
Basic Installation and Configuration
3-31
v1.0, September 2005
5.
Click
Apply
to save your settings.
Changing the Basic IP Settings Options
The Basic IP Settings menu is under the Basic heading of the main menu. Use this menu to
configure DHCP, static IP, and access point name settings.
•
Access Point Name (NetBIOS)
Enter a new name for the wireless access point and click Apply to save your changes.
•
The IP Address
The wireless access point is shipped preconfigured with its DHCP client disabled and with the
following private static IP addresses:
–
–
IP Subnet Mask — 255.255.255.0
–
Gateway — 0.0.0.0
Figure 3-16
Page 54 / 82
Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG102
3-32
Basic Installation and Configuration
v1.0, September 2005
–
Primary and Secondary DNS Servers — 0.0.0.0
If your network has a requirement to use a different IP addressing scheme, you can make those
changes in this menu. These settings are only required if the “Use this IP address” radio button
is chosen. Remember to click Apply to save your changes.
•
Time Zone
Select the time zone location for your setting.
Note:
You must have an Internet connection to get the current time.
Page 55 / 82
Management
4-1
v1.0, September 2005
Chapter 4
Management
This chapter describes how to use the management features of your WAG102 ProSafe Dual Band
Wireless Access Point. These features can be found by clicking on the Maintenance heading in the
Main Menu of the browser interface.
Remote Management
The Remote Management screen lets you specify the simple network management protocol
(SNMP) parameters.
Fill out the remote management information:
•
SNMP
–
Enable SNMP to allow the SNMP network management software, such as HP OpenView,
to manage the wireless access point via SNMPv1/v2 protocol.
–
Public Community Name
: The community string to allow the SNMP manager to read the
wireless access point's MIB objects. The default is public.
–
Private Community Name
: The community string to allow the SNMP manager to read
and write the wireless access point's MIB objects. The default is private.
Figure 4-1
19216811.live