Page 101 / 400
Scroll up to view Page 96 - 100
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Switching Commands
8-33
202-10088-01, March 2005
Mode
Global Config
no snmp-server enable traps linkmode
This command disables Link Up/Down traps for the entire switch.
Format
no snmp-server enable traps linkmode
Mode
Global Config
snmp-server enable traps multiusers
This command enables Multiple User traps. When the traps are enabled, a Multiple User Trap is
sent when a user logs in to the terminal interface (EIA 232 or telnet) and there is an existing
terminal interface session.
Default
enabled
Format
snmp-server enable traps multiusers
Mode
Global Config
no snmp-server enable traps multiusers
This command disables Multiple User traps.
Format
no snmp-server enable traps multiusers
Mode
Global Config
snmp-server enable traps stpmode
This command enables the sending of new root traps and topology change notification traps.
Default
enabled
Format
snmp-server enable traps stpmode
Mode
Global Config
no snmp-server enable traps stpmode
This command disables the sending of new root traps and topology change notification traps.
Format
no snmp-server enable traps stpmode
Mode
Global Config
Page 102 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
8-34
Switching Commands
202-10088-01, March 2005
snmptrap
This command adds an SNMP trap name. The maximum length of name is 16 case-sensitive
alphanumeric characters.
Default
The default name for the six undefined community names is
Delete.
Format
snmptrap <
name> <ipaddr>
Mode
Global Config
no snmptrap
This command deletes trap receivers for a community.
Format
no snmptrap <
name> <ipaddr>
Mode
Global Config
snmptrap ipaddr
This command assigns an IP address to a specified community name. The maximum length of
name is 16 case-sensitive alphanumeric characters.
Note:
IP addresses in the SNMP trap receiver table must be unique. If you make multiple entries
using the same IP address, the first entry is retained and processed. All duplicate entries are
ignored.
Format
snmptrap ipaddr <
name> <ipaddrold
> <
ipaddrnew>
Mode
Global Config
snmptrap mode
This command activates or deactivates an SNMP trap. Enabled trap receivers are active (able to
receive traps). Disabled trap receivers are inactive (not able to receive traps).
Format
snmptrap mode <
name> <ipaddr>
Mode
Global Config
no snmptrap mode
This command deactivates an SNMP trap. Disabled trap receivers are inactive (not able to receive
traps).
Page 103 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Switching Commands
8-35
202-10088-01, March 2005
Format
no snmptrap mode <
name> <ipaddr>
Mode
Global Config
snmp trap link-status
This command enables link status traps by interface.
Note:
This command is valid only when the Link Up/Down Flag is enabled. See ‘snmp-server enable traps
linkmode’ command.
Format
snmp trap link-status
Mode
Interface Config
no snmp trap link-status
This command disables link status traps by interface.
Note:
This command is valid only when the Link Up/Down Flag is enabled. See ‘snmp-server enable traps
linkmode’ command).
Format
no snmp trap link-status
Mode
Interface Config
snmp trap link-status all
This command enables link status traps for all interfaces.
Note:
This command is valid only when the Link Up/Down Flag is enabled (see “snmp-server enable traps
linkmode” ).
Format
snmp trap link-status all
Mode
Global Config
no snmp trap link-status all
This command disables link status traps for all interfaces.
Note:
This command is valid only when the Link Up/Down Flag is enabled (see “snmp-server enable traps
linkmode”).
Format
no snmp trap link-status all
Mode
Global Config
Page 104 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
8-36
Switching Commands
202-10088-01, March 2005
Management VLAN Command
This command is used to set the Management VLAN.
network mgmt_vlan
This command configures the Management VLAN ID.
Default
1
Format
network mgmt_vlan
<1-4094>
Mode
Privileged EXEC
System Configuration Commands
This chapter provides a detailed explanation of the System configuration commands. The
commands are divided into two functional groups:
•
Show commands display switch settings, statistics, and other information.
•
Configuration commands configure features and options of the switch. For every
configuration command, there is a show command that displays the configuration setting.
addport
This command adds one port to the port-channel (LAG). The first interface is a
logical slot and port number of a configured port-channel.
Note:
Before adding a port to a port-channel, set the physical mode of the port. See ‘speed’
command.
Format
addport
<
logical
slot/port
>
Mode
Interface Config
auto-negotiate
This command enables automatic negotiation on a port. The default value is enable.
Format
auto-negotiate
Page 105 / 400
User Manual for the NETGEAR 7300S Series Layer 3 Managed Switch Software
Switching Commands
8-37
202-10088-01, March 2005
Mode
Interface Config
no auto-negotiate
This command disables automatic negotiation on a port.
Note:
Automatic sensing is disabled when automatic negotiation is disabled.
Format
no auto-negotiate
Mode
Interface Config
auto-negotiate all
This command enables automatic negotiation on all ports. The default value is enable.
Format
auto-negotiate all
Mode
Global Config
no auto-negotiate all
This command disables automatic negotiation on all ports.
Format
no auto-negotiate all
Mode
Global Config
deleteport (Interface Config)
This command deletes the port from the port-channel (LAG). The interface is a
logical unit, slot and port slot and port number of a configured port-channel.
Format
deleteport
<
logical
slot/port
>
Mode
Interface Config
deleteport (Global Config)
This command deletes all configured ports from the port-channel (LAG). The
interface is a logical unit, slot and port slot and port number of a configured port-
channel.
Format
deleteport
{<
logical
slot/port
> | all}
Mode
Global Config
19216811.live