1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. DGN1000SP
    5. /
  5. 4
Page 16 / 39 Scroll up to view Page 11 - 15
Installing Your Router Manually (Advanced, Mac, and Linux Users)
12
Understanding ADSL Microfilters
ADSL technology uses the same wires as your telephone service. However, ADSL adds signals to
the telephone lines which create noise in the telephone service. You must use ADSL microfilters
to filter out these signals before they reach your telephone.
ADSL Microfilter
Each device such as a telephone, fax machine, answering machine, or caller ID display will require
an ADSL microfilter.
ADSL Microfilter with Built-In Splitter
Use an ADSL microfilter with built-in splitter when there is a single wall outlet which must
provide connectivity for both the wireless modem router and telephone equipment.
If you purchased the wireless modem router in a country where a microfilter is not
included, you must acquire one.
Figure 4
Do not connect the wireless modem router to the ADSL line through a microfilter
unless the microfilter is a combination microfilter/splitter specifically designed for
this purpose. Doing so will prevent block your connection to the Internet. If you
have any doubts about this, connect the wireless modem router directly to the
ADSL line.
Figure 5
Page 17 / 39
Installing Your Router Manually (Advanced, Mac, and Linux Users)
13
Connecting Your Wireless Modem Router
Before you install your wireless modem router, make sure that the Internet Protocol (TCP/IP)
Property settings on your computer are set to “automatically obtain an IP address” using DHCP
and “Obtain DNS server address automatically.” You can check these settings by looking at the
TCP/IP Properties of your Internal Network Connections, which are accessible through the
Control Panel of your computer. If you are unsure about this, refer to the documentation for your
computer or see the link to TCP/IP Addressing in
“Related Documents” on page 34
.
To connect the wireless modem router, the ADSL filter and the computer:
1.
Connect an ADSL filter as shown below.
•
Install an ADSL filter for every telephone that uses the same phone line as your wireless
modem router. Select the appropriate filter(s) for your wireless setup.
If you are replacing an existing router, disconnect it completely from your network
and set it aside before starting to install your new router.
If you purchased the DGN1000 in a country where an ADSL filter is not
included, you must acquire one.
1.
One-Line Filter: Use with a phone or fax machine.
2.
Splitter: Use with a one-line filter to share an outlet with a phone and the wireless
modem router.
3.
Two-Line Filter with Splitter: Use to share an outlet with a phone and the wireless
modem router.
Figure 6
1
2
3
Page 18 / 39
Installing Your Router Manually (Advanced, Mac, and Linux Users)
14
•
Two-Line Filter Example
. Insert the two-line filter into the phone outlet and connect the
phone to the phone line connector (
A
), as shown in
Figure 7
.
2.
Connect the wireless modem router to the ADSL filter. Using the included phone cable with
RJ-11 jacks, connect the ADSL port (
B
)
of the wireless modem router to the ADSL port (
C
)
of
the two-line filter, as shown in
Figure 8
.
Figure 7
To use a one-line filter with a separate splitter, insert the splitter into the phone
outlet, connect the one-line filter to the splitter, and connect the phone to the
filter.
A
Page 19 / 39
Installing Your Router Manually (Advanced, Mac, and Linux Users)
15
.
3.
Connect the Ethernet cable (
D
)
from a wireless modem router LAN port to the Ethernet
adapter in your computer, as shown in
Figure 9
.
4.
Connect the power adapter to the wireless modem router and plug it in to a power outlet.
Figure 8
Improperly connecting a filter to your wireless modem router will block
your ADSL connection.
C
B
Page 20 / 39
Installing Your Router Manually (Advanced, Mac, and Linux Users)
16
5.
Connect any additional wired PCs to your router by inserting an Ethernet cable from a PC into
one of the three remaining LAN ports.
Verifying Your Connection
Verify that your router is connected correctly by checking the wireless modem router status lights.
•
The power light is lit after turning on the wireless modem router.
•
The DSL light is lit, indicating an ADSL connection.
•
The wireless light is lit after turning on the wireless modem router.
•
The Internet light is green, indicating you are connected to the ADSL network.
Now, turn on your computer. If software usually logs you in to your Internet connection, do not run
that software. Cancel it if it starts automatically. Verify the following:
•
The local lights (1 through 4) are lit for any connected computers.
Figure 9
D
D
D

Rate

4.5 / 5 based on 2 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top