Page 36 / 39 Scroll up to view Page 31 - 35
Technical Specifications
32
Default Configuration
To reset you router to the default settings, see
“Restoring the Default Configuration and Password”
on page 30
. Your router will return to the factory configuration settings that are shown in the table
below.
Interface Specifications
LAN:
10BASE-T or 100BASE-Tx, RJ-45
WAN:
ADSL, Dual RJ-11, pins 2 and 3
T1.413, G.DMT, G.Lite
Feature
Default Behavior
Router Login
User Login URL
or
User Name (case sensitive)
admin
Login Password (case sensitive)
password
Internet Connection
WAN MAC Address
Use Default address
WAN MTU Size
1492
Port Speed
AutoSense
Local Network (LAN)
Lan IP
192.168.0.1
Subnet Mask
255.255.255.0
RIP Direction
None
RIP Version
Disabled
RIP Authentication
None
DHCP Server
Enabled
DHCP Starting IP Address
192.168.0.2
DHCP Ending IP Address
192.168.0.254
DMZ
Disabled
Time Zone
GMT
Page 37 / 39
Technical Specifications
33
Time Zone Adjusted for Daylight Saving
Time
Disabled
SNMP
Disabled
Firewall
Inbound (communications coming in from
the Internet)
Disabled (except traffic on port 80, the http port)
Outbound (communications going out to
the Internet)
Enabled (all)
Source MAC filtering
Disabled
Wireless
Wireless Communication
Enabled
SSID Name
NETGEAR
Security
Disabled
Broadcast SSID
Enabled
Transmission Speed
Auto
a
Country/Region
United States (in North America; otherwise, varies by
region)
RF Channel
Auto
Operating Mode
Up to 130 Mbps
Data Rate
Best
Output Power
Full
Access Point
Enabled
Authentication Type
Open System
Wireless Card Access List
All wireless stations allowed
a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
Feature
Default Behavior
Page 38 / 39
Related Documents
34
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
ITCP/IP Networking Basics
Wireless Networking Basics
Preparing Your Network
Virtual Private Networking Basics
Glossary
Page 39 / 39
35
Registration and Certifications
Product Registration, Support, and Documentation
Register your product at
You must register before you can use our telephone
support service. Product updates and Web support are always available by going to:
.
Setup documentation is available on the CD, on the support website, and on the documentation website
.
When the
wireless modem router is connected to the Internet, click the KnowledgeBase link to view support information or click
the Documentation link to view the online
User Manual
for this wireless modem router.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top