Page 51 / 78
Scroll up to view Page 46 - 50
Advanced Settings
Rev 1
Oct.13
51
3.
Click
Activate
.
4.
Enter your PIN and click
Submit
.
You are allowed 5 attempts to enter the correct PIN. If you run out of available
attempts the PIN will be locked. If this happens, contact your network provider to
receive a PUK number to unlock the PIN.
Page 52 / 78
AirCard 782S Mobile Hotspot User Guide
52
2400353
Configure mobile broadband
View WAN information
To view network information, such as the active network, connection status, signal
strength, etc.:
1.
On the Homepage, click
Settings > Network > Status Details
.
Enable port forwarding
If your computer is hosting a server, you can enable port forwarding so that other users
can access the server.
To enable port forwarding:
1.
On the Homepage, log in as Administrator.
2.
Click
Settings > Router > Port Forwarding
.
Page 53 / 78
Advanced Settings
Rev 1
Oct.13
53
3.
Select
Enable
beside Port Forwarding. The Port Forwarding list will appear.
Incoming traffic is forwarded to specific ports and devices on your network (using
their local IP addresses).
Note: Port forwarding creates a security risk. When not required, port forwarding
should be disabled.
4.
Enter the port forwarding information and click
Submit
. (Submit button appears
once you make a selection.)
Enable port filtering
Port filtering enables you to select which applications (for example, http, ftp, email
servers) can access the Internet. Used in conjunction with other security measures such
as firewall, port filtering can enhance network security.
To enable port filtering:
1.
On the Homepage, log in as Administrator.
2.
Click
Settings > Router > Port Filtering
.
3.
Select the Port Filtering Mode:
·
Black List (Block list) — Specific applications not allowed to access the Internet
·
White List (Allow list) — Specific applications allowed to access the Internet
Note:
Only one list at a time can be active, either a Black List or a White List.
Page 54 / 78
AirCard 782S Mobile Hotspot User Guide
54
2400353
4.
Identify the ports to filter — enter a meaningful label that describes the service, and
the port and communication protocol being used.
5.
Once you have identified the desired applications, click
Submit
. (Submit button
appears once you make a selection.)
Enable VPN passthrough
If you want to connect to a corporate network using VPN, you first need to enable VPN
connections (passthrough).
To enable VPN passthrough:
1.
On the Homepage, log in as Administrator.
2.
Click
Settings > Router > Basic
.
3.
In the LAN section, select
On
beside VPN Passthrough, and click
Submit
. (Submit
button appears once you make a selection.)
Configure APN details
Your mobile hotspot comes preconfigured with the APN (Access Point Name) for your
network service provider.
The APN is checked to determine the type of network connection to establish.
Page 55 / 78
Advanced Settings
Rev 1
Oct.13
55
To add an APN for another network:
1.
On the Homepage, log in as Administrator.
2.
Click
Settings > Network > APN
.
3.
In the blank line, enter the Name of the network service provider and the APN you
obtained from them.
4.
Enter the Username and Password, if these are required for the wireless network.
5.
Select the network Authentication mode. The options are:
·
None (default)
·
PAP
·
CHAP
·
PAP or CHAP
6.
Click
beside the new APN entry.
To select the APN to use:
1.
Select
Active
beside the APN entry to be used.
To remove an APN entry:
1.
Click
beside the APN entry.
Enable DMZ
In a DMZ (demilitarized zone) network configuration, a computer runs outside the
firewall in the DMZ. This computer intercepts incoming Internet traffic, providing an
extra layer of protection for the rest of the network.
To enable DMZ and designate a computer to screen incoming traffic:
1.
On the Homepage, log in as Administrator.
2.
Click
Settings > Router > Basic
.
3.
Select
On
beside DMZ Enabled.
19216811.live