1. Home
    2. /
  2. Manuals
    3. /
  3. NETGEAR
    4. /
  4. AC1450
    5. /
  5. 24
Page 116 / 128 Scroll up to view Page 111 - 115
Troubleshooting
116
AC1450 Smart WiFi Router
Cannot Log In to the Router
If you are unable to log in to the router from a computer on your local network, check the
following:
•
If you are using an Ethernet-connected computer, check the Ethernet connection
between the computer and the router.
•
Make sure that the IP address of your computer is on the same subnet as the router. If
you are using the recommended addressing scheme, your computer’s address should be
in the range of 192.168.1.2 to 192.168.1.254.
•
If your computer’s IP address is shown as 169.254.x.x, recent versions of Windows and
Mac OS generate and assign an IP address if the computer cannot reach a DHCP server.
These autogenerated addresses are in the range of 169.254.x.x. If your IP address is in
this range, check the connection from the computer to the router, and reboot your
computer.
•
If your router’s IP address was changed and you do not know the current IP address,
clear the router’s configuration to factory defaults. This sets the router’s IP address to
192.168.1.1. For more information, see
Factory Settings
on page
123.
•
Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click
Refresh
to be sure that the Java applet is loaded.
•
Try quitting the browser and launching it again.
•
Make sure that you are using the correct login information. The factory default login name
is
admin
, and the password is
password
. Make sure that Caps Lock is off when you
enter this information.
•
If you are attempting to set up your NETGEAR router as an additional router behind an
existing router in your network, consider replacing the existing router. NETGEAR does
not support such a configuration.
•
If you are attempting to set up your NETGEAR router as a replacement for an ADSL
gateway in your network, the router cannot perform many gateway services. For
example, the router cannot convert ADSL or cable data into Ethernet networking
information. NETGEAR does not support such a configuration.
Cannot Access the Internet
If you can access your router but not the Internet, check to see if the router can obtain an IP
address from your Internet service provider (ISP). Unless your ISP provides a fixed IP
address, your router requests an IP address from the ISP. You can determine whether the
request was successful using the Router Status screen.
To check the WAN IP address:
1.
Start your browser, and select an external site such as
www.netgear.com
.
2.
Access the router interface at
www.routerlogin.net
.
3.
Select
Administration > Router Status
.
Page 117 / 128
Troubleshooting
117
AC1450 Smart WiFi Router
4.
Check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your router has
not obtained an IP address from your ISP.
If your router cannot obtain an IP address from the ISP, you might need to force your cable or
DSL modem to recognize your new router by restarting your network. For more information,
see
Sequence to Restart Your Network
on page
113.
If your router is still unable to obtain an IP address from the ISP, the problem might be one of
the following:
•
Your Internet service provider (ISP) might require a login program.
Ask your ISP whether they require PPP over Ethernet (PPPoE) or some other type of
login.
•
If your ISP requires a login, the login name and password might be set incorrectly.
•
Your ISP might check for your computer’s host name.
Assign the computer host name of your ISP account as the account name in the Internet
Setup screen.
•
Your ISP allows only one Ethernet MAC address to connect to Internet and might check
for your computer’s MAC address. In this case, do one of the following:
-
Inform your ISP that you have bought a new network device, and ask them to use the
router’s MAC address.
-
Configure your router to clone your computer’s MAC address.
If your router can obtain an IP address, but your computer is unable to load any web pages
from the Internet:
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www
addresses) to numeric IP addresses. Typically, your ISP provides the addresses of one or
two DNS servers for your use. If you entered a DNS address during the router’s
configuration, reboot your computer, and verify the DNS address. You can configure your
computer manually with DNS addresses, as explained in your operating system
documentation
.
•
Your computer might not have the router configured as its TCP/IP gateway.
If your computer obtains its information from the router by DHCP, reboot the computer,
and verify the gateway address.
•
You might be running login software that is no longer needed.
If your ISP provided a program to log you in to the Internet (such as WinPoET), you no
longer need to run that software after installing your router. You might need to go to
Internet Explorer and select
Tools > Internet Options
, click the
Connections
tab, and
select
Never dial a connection
.
Page 118 / 128
Troubleshooting
118
AC1450 Smart WiFi Router
Troubleshoot PPPoE
If you are using PPPoE, try troubleshooting your Internet connection.
To troubleshoot a PPPoE connection:
1.
Select
Administration > Router Status
.
2.
Click
Connection Status
.
3.
Check to see if your PPPoE connection is up and working.
4.
If any of the field s on the Connection Status screen indicate Failed, you can attempt to
reconnect by clicking
Connect
. The router continues to attempt to connect indefinitely.
5.
If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There might also be a provisioning problem with your ISP.
Note:
Unless you connect manually, the router does not authenticate using
PPPoE until data is transmitted to the network.
Troubleshoot Internet Browsing
If your router can obtain an IP address but your computer is unable to load any web pages
from the Internet, check the following:
•
Your computer might not recognize any DNS server addresses. A DNS server is a host
on the Internet that translates Internet names (such as www addresses) to numeric IP
addresses.
Typically, your ISP provides the addresses of one or two DNS servers for your use. If you
entered a DNS address during the router’s configuration, restart your computer.
Alternatively, you can configure your computer manually with a DNS address, as
explained in the documentation for your computer.
•
Your computer might not have the router configured as its default gateway.
Reboot the computer and verify that the router address (www.routerlogin.net) is listed by
your computer as the default gateway address.
•
You might be running log in software that is no longer needed. If your ISP provided a
program to log you in to the Internet (such as WinPoET), you no longer need to run that
software after installing your router. You might need to go to Internet Explorer and select
Tools > Internet Options
, click the
Connections
tab, and select
Never dial a
connection
.
Page 119 / 128
Troubleshooting
119
AC1450 Smart WiFi Router
Changes Not Saved
If the router does not save the changes you make in the router interface, check the following:
•
When entering configuration settings, always click the
Apply
button before moving to
another screen or tab, or your changes are lost.
•
Click the
Refresh
or
Reload
button in the web browser. The changes might have
occurred, but the old settings might be in the web browser’s cache.
Wireless Connectivity
If you are having trouble connecting wirelessly to the router, try to isolate the problem.
•
Does the wireless device or computer that you are using find your wireless network?
If not, check the WiFi LED on the front of the router. If it is off, you can press the
WiFi
On/Off
button on the side of the router to turn the router wireless radios back on.
If you disabled the router’s SSID broadcast, then your wireless network is hidden and
does not show up in your wireless client’s scanning list. (By default, SSID broadcast is
enabled.)
•
Does your wireless device support the security that you are using for your wireless
network (WPA or WPA2)?
•
If you want to view the wireless settings for the router, use an Ethernet cable to connect a
computer to a LAN port on the router. Then log in to the router, and select
Wireless
see
(
Basic Wireless Settings
on page
24).
Note:
Be sure to click
Apply
if you change settings.
Wireless Signal Strength
If your wireless device finds your network, but the signal strength is weak, check these
conditions:
•
Is your router too far from your computer, or too close? Place your computer near the
router, but at least 6 feet (1.8 meters) away, and see whether the signal strength
improves.
•
Are objects between the router and your computer blocking the wireless signal?
Page 120 / 128
Troubleshooting
120
AC1450 Smart WiFi Router
Troubleshoot Your Network Using the Ping Utility
Most network devices and routers contain a ping utility that sends an echo request packet to
the designated device. The device then responds with an echo reply. You can easily
troubleshoot a network is easy using the ping utility in your computer or workstation.
Test the LAN Path to Your Router
You can ping the router from your computer to verify that the LAN path to your router is set up
correctly.
To ping the router from a Windows computer:
1.
From the Windows toolbar, click
Start
and select
Run
.
2.
In the field provided, type
ping
followed by the IP address of the router, as in this example:
ping www.routerlogin.net
3.
Click
OK
.
You should see a message like this one:
Pinging <IP address > with 32 bytes of data
If the path is working, you see this message:
Reply from < IP address >: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
Wrong physical connections
For a wired connection, make sure that the numbered LAN port LED is lit for the port to
which you are connected.
Check that the appropriate LEDs are on for your network devices. If your router and
computer are connected to a separate Ethernet switch, make sure that the link LEDs are
lit for the switch ports that are connected to your computer and router.
•
Wrong network configuration
Verify that the Ethernet card driver software and TCP/IP software are both installed and
configured on your computer.
Verify that the IP address for your router and your computer are correct and that the
addresses are on the same subnet.

Rate

4 / 5 based on 3 votes.

Popular NETGEAR Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top