Page 46 / 62 Scroll up to view Page 41 - 45
NP805N
Gigabit Wireless Router
46
NetComm NP805N - Gigabit Wireless Router
YMLO-805N
www.netcomm.com.au
Scheduling
You can use scheduling to enable or disable a service at a specific time or on a specific day.
Select "Enable" and then click the "New Add" button.
Select a name for the rule and enter the details such as the day, start time or end time and click "Save"
In the example below, the
rule is called “Work Hours” and it is only active between 08:00 and 17:30.
You are then able to select the scheduling rule name specified from the Packet Filter configuration section to perform the configured
filtering at the scheduled time as per the screenshot below.
This example would prevent any access to the IP address 66.102.11.104 from any device connected to the router, 7 days a week,
only between the hours of 08:00 and 17:30.
Click "Save" to save the settings or "Undo" to cancel.
Page 47 / 62
www.netcomm.com.au
47
NetComm NP805N
Gigabit Wireless Router
YMLO-805N
IPv6
The IPv6 page enables you to configure the settings used for an IPv6 connection (if supported by your Internet Service Provider).
OPTION
DEFINITION
IPv6
Select to enable or disable IPv6 functionality.
IPv6 Connection
Select the type of IPv6 connection to utilise for your service. You can select from:
Static IPv6
DHCPv6
PPPoE
6 to 4
IPv6 in IPv4 Tunnel
Select the type of connection as required by your Internet Service Provider for their IPv6 service and then enter the
appropriate details are provided by them in the applicable fields.
LAN IPv6 Address
The IP Address to use for the IPv6 service connection.
LAN IPv6 Link-Local Address
The current local LAN IPv6 address of the NP805N.
Autoconfiguration
Select to enable or disable IPv6 auto configuration (if supported by your Internet Service Provider).
Autoconfiguration Type
Select the applicable type of auto configuration mode as required by your Internet Service Provider for their IPv6 service.
Router Advertisement Lifetime
Enter the length of time between the router advertising its availability on the IPv6 connection.
Page 48 / 62
NP805N
Gigabit Wireless Router
48
NetComm NP805N - Gigabit Wireless Router
YMLO-805N
www.netcomm.com.au
TR-069
The TR-069 client enables the NP805N to be automatically configured from an appropriate TR-069 server. Enter the applicable
configuration options to enable the router to contact the TR-069 server and retrieve any configuration options.
OPTION
DEFINITION
TR-069
Select to enable or disable the TR-069 automatic configuration function.
ACS URL
Enter the URL of the ACS server for automatic configuration.
ACS User Name
The username required to login to the ACS server.
ACS Password
The password required to login to the ACS server.
Connection Request Port
The port number the ACS server is running on.
Connection Request Username
The username to use when a connection request is made to the CPE.
Connection Request Password
The password to use when a connection request is made to the CPE.
Inform
Select to enable or disable the Inform function for ACS connections.
Interval
Select the interval between Inform requests if Inform has been enabled.
Once configured, click the “Save” button to store any changes to the settings.
Page 49 / 62
www.netcomm.com.au
49
NetComm NP805N
Gigabit Wireless Router
YMLO-805N
VLAN
The VLAN page enables you to configure VLAN tagging for the Ethernet ports. VLAN tagging can be used to separate network
traffic so that it is not visible to other VLANs. The currently configured VLAN tagging settings are shown at the bottom of the page.
1.
Enter the VLAN ID to be used for a particular Ethernet port.
2.
Select whether or not to mark transmitted packets with the selected VLAN ID.
3.
Click “Save”.
You can also set the WAN port to a particular VLAN (if needed). To do this, perform the following steps:
1.
Click
the “WAN VLAN Settings” button.
2.
Select the appropriate VLAN ID.
3.
Select the appropriate Routing Type for the WAN interface to use.
4.
Click “Save”.
Page 50 / 62
NP805N
Gigabit Wireless Router
50
NetComm NP805N - Gigabit Wireless Router
YMLO-805N
www.netcomm.com.au
NAS Settings
The NAS Settings page enables you to configure the network area storage (NAS) function of the NP805N. This function can be
used to remotely access files stored on an attached USB hard drive. Click on any of the menu items to access the respective
configuration page.
Disk Utility
The Disk Utility function enables you to check any attached USB storage for errors. The NP805N will scan the attached storage and
determine if there are any file system errors present. File System errors can prevent you being able to access stored content. You
can also format (erase) any attached storage if needed. Simply click the appropriate button to perform either task.
File Sharing
The File Sharing function enables the NP805N to take part in a Windows networking environment. Once configured, the attached
USB Storage can be viewed from Windows by typing:
\\<Configured NP805N Computer Name>\Storage\
Files can then be dragged and dropped onto the attached USB storage.
OPTION
DEFINITION
Computer Name
Enter the computer name the NP805N is to use on the network.
WorkGroup
Enter the network workgroup the NP805N is to be a member of.
Server Comment
Enter the comment to be displayed when a list of network hosts is shown.
The File Sharing configuration also enables you to enable the built-in FTP server function and the associated settings:
OPTION
DEFINITION
FTP
Select to enable or disable the FTP server function.
FTP Port
Enter the network port the FTP server should run on.
FTP Max Connections per IP
Enter the maximum number of concurrent connections which can be used by a particular IP address.
FTP Max Clients
Enter the maximum number of clients which can connect to the FTP concurrently.
Client Support UTF8
Enable Unicode support for connected clients.
Codepage
Select the appropriate codepage to use for the filenames of files stored on the FTP server.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top