1. Home
    2. /
  2. Manuals
    3. /
  3. NetComm
    4. /
  4. 3G9WB
    5. /
  5. 8
Page 36 / 86 Scroll up to view Page 31 - 35
36 – YML902
Management
The Management menu has the following maintenance functions and processes:
6.1 Device Settings
6.2 Access Control
6.3 Simple Network Time Protocol (SNTP)
6.4 Save and Reboot
6.1
Device Settings
The Device Settings screens allow you to backup, retrieve and restore the default settings of your Router. It
also provides a function for you to update your Routers firmware.
6.1.1
Backup Settings
The following screen appears when Backup is selected. Click the Backup Settings button to save the current
configuration settings.
You will be prompted to define the location of a backup file to save to your PC.
Downloaded from
www.Manualslib.com
manuals search engine
Page 37 / 86
3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE
YML902 – 37
6.1.2
Update Settings
The following screen appears when selecting Update from the submenu. By clicking on the Browse button, you
can locate a previously saved filename as the configuration backup file. Click on the Update settings to load it.
6.1.3
Restore Default
The following screen appears when selecting Restore Default. By clicking on the Restore Default Settings
button, you can restore your Routers default firmware settings. To restore system settings, reboot your Router.
NOTE:
The default settings can be found in section 3.1 Default Settings.
Once you have selected the Restore Default Settings button, the following screen will appear. Close the
window and wait 2 minutes before reopening your browser. If required, reconfigure your PCs IP address to
match your new configuration(see section 3.2 TCP/IP Settings for details).
After a successful reboot, the browser will return to the Device Info screen.
If the browser does not refresh to
the default screen, close and restart the browser.
NOTE:
The Restore Default function has the same effect as the reset button.
The device board hardware and the boot loader support the
reset to default button.
If the reset button is continuously pushed for more than 5 seconds (and not more than 12 seconds), the
boot loader will erase the configuration settings saved on flash memory.
Downloaded from
www.Manualslib.com
manuals search engine
Page 38 / 86
38 – YML902
6.1.4
Update Firmware
The following screen appears when selecting Update Firmware. By following this screens steps, you can
update your Routers firmware. Manual device upgrades from a locally stored file can also be performed using
the following screen.
1:
Obtain an updated software image file
2:
Enter the path and filename of the firmware image file in the Software File Name field or click the Browse
button to locate the image file.
3:
Click the Update Software button once to upload and install the file.
NOTE:
The update process will take about 2 minutes to complete.
The Router will reboot and the browser window will refresh to the
default screen upon successful installation.
It is recommended that you compare the Software Version at the top of the Basic screen (WUI homepage) with the firmware
version installed, to confirm the installation was successful.
Downloaded from
www.Manualslib.com
manuals search engine
Page 39 / 86
3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE
YML902 – 39
6.2
Access Control
The Access Control option found in the Management drop down menu, configures access related parameters
in the following three areas:
•
Services
•
IP Addresses
•
Passwords
Access Control is used to control local and remote management settings for your Router.
6.2.1
Services
The Service Control List (SCL) allows you to enable or disable your Local Area Network (LAN) or Wireless Area
Network (WAN) services by ticking the checkbox as illustrated below. These access services are available: FTP,
HTTP, ICMP, SSH, TELNET, and TFTP.
Click Save/Apply to continue.
Downloaded from
www.Manualslib.com
manuals search engine
Page 40 / 86
40 – YML902
6.2.2
IP Address
The IP Address option limits local access by IP address.
When the Access Control Mode is enabled, only the
IP addresses listed here can access the device.
Before enabling Access Control Mode, add IP addresses with
the Add button.
On this screen, enter the IP address of a local PC which you wish to allow
permission. Click Save/Apply to
continue.
6.2.3
Passwords
The Passwords option configures your account access password for your Router. Access to the device is
limited to the following three user accounts:
•
admin
is to be used for local unrestricted access control
•
support
is to be used for remote maintenance of the device
•
user
is to be used to view information and update device firmware
Use the fields illustrated in the screen below to change or create your password.
Passwords must be 16
characters or less with no spaces.
Click Save/Apply to continue.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.3 / 5 based on 3 votes.

Popular NetComm Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top