Page 31 / 86
Scroll up to view Page 26 - 30
3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE
YML902 – 31
Option
Description
54g Mode
Select Auto mode for greatest compatibility.
Select Performance mode for the fastest
performance among 54g certified equipment.
Select LRS mode if you are experiencing
difficulty with legacy 802.11b equipment.
If this does not work, you may also try
802.11b only mode.
54g Protection
In Auto mode, the router will use RTS/CTS to improve 802.11g performance in mixed
802.11g/802.11b networks.
Turning protection Off will maximize 802.11g throughput
under most conditions.
Preamble Type
Short preamble is intended for applications where maximum throughput is desired but
it does not work with legacy equipment.
Long preamble works with the current 1 and 2
Mbit/s DSSS specification as described in IEEE Std 802.11-1999
Transmit Power
Set the power output (by percentage) as desired.
Downloaded from
www.Manualslib.com
manuals search engine
Page 32 / 86
32 – YML902
5.4
MAC Filter
This screen appears when Media Access Control (MAC) Filter is selected. This option allows access to be
restricted based upon the unique 48-bit MAC address.
To add a MAC Address filter, click the
Add
button shown below.
To delete a filter, select it from the table below and click the
Remove
button.
Option
Description
MAC Restrict Mode
Disabled
– Disables MAC filtering
Allow
– Permits access for the specified MAC addresses.
NOTE:
Add a wireless device’s MAC address before clicking the Allow radio button or else you will need
to connect to the Router’s web user interface using the supplied yellow Ethernet cable and add
the wireless device’s MAC address.
Deny
– Rejects access for the specified MAC addresses
MAC Address
Lists the MAC addresses subject to the MAC Restrict Mode.
The Add button prompts an
entry field that requires you type in a MAC address in a two-character, 6-byte convention:
xx:xx:xx:xx:xx:xx where xx are hexadecimal numbers.
A maximum of 60 MAC addresses
can be added.
Enter the MAC address on the screen below and click
Save/Apply
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 33 / 86
3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE
YML902 – 33
5.5
Wireless Bridge
The following screen appears when selecting Wireless Bridge, and goes into a detailed explanation of how to
configure wireless bridge features of the wireless LAN interface.
Click
Save/Apply
to implement new configuration settings.
Feature
Options
AP Mode
Selecting
Wireless Bridge
(Wireless Distribution System) disables Access Point (AP)
functionality while selecting
Access Point
enables AP functionality.
In
Access Point
mode, wireless bridge functionality will still be available and wireless stations will be able
to associate to the AP.
Bridge Restrict
Selecting
Disabled
in Bridge Restrict disables Wireless Bridge restriction, which means
that any wireless bridge will be granted access.
Selecting Enabled or Enabled (Scan)
allows wireless bridge restriction.
Only those bridges selected in Remote Bridges will be
granted access.
Click
Refresh
to update the station list when Bridge Restrict is enabled.
Downloaded from
www.Manualslib.com
manuals search engine
Page 34 / 86
34 – YML902
5.6
Station Info
The following screen appears when you select Station Info, and shows authenticated wireless stations and
their status.
Click the
Refresh
button to update the list of stations in the WLAN.
BSSID
The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within
an area.
In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control)
address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID
is generated randomly.
Associated
Lists all the stations that are associated with the Access Point, along with the amount of
time since packets were transferred to and from each station.
If a station is idle for too
long, it is removed from this list.
Authorized
Lists those devices with authorized access.
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live