NetComm 3G9WB Router Manual PDF (Setup & Configuration Guide)

Page 71 / 86 Scroll up to view Page 66 - 70

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

YML902 – 71

CLI commands via Telnet

Show all CLI commands

Description: List all available CLI commands that the 3G router supports.

Synopsis: help | ?

Example:

> help

?

help

logout

reboot

atm

ddns

dumpcfg

ping

sntp

sysinfo

tftp

wlan

sierra

qos

version

build

Downloaded from

www.Manualslib.com

manuals search engine

Page 72 / 86

72 – YML902

End the telnet session

Description: End the telnet session

Synopsis: logout

Example:

> logout

Reset/reboot device

Description: To reboot the router.

Synopsis: reboot

Example:

> reboot

Radio Signal Strength

Description: Display the 3G radio signal strength.

Synopsis: sierra show --signal

Example:

> sierra show --signal

signal:

23

Note: Signal value is explain in the table below

Value

2 ~ 5

6 ~ 10

11 ~ 13

14 ~ 17

18 ~ 31

99

Signal level

in dBm

-109 ~ -103

-101 ~ -93

-91 ~ -87

-85 ~ -79

-77 ~ -52

unknown

5 Signal bars

LED

Low

Medium

High

Downloaded from

www.Manualslib.com

manuals search engine

Page 73 / 86

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

YML902 – 73

Radio Band

Description: Display the 3G band

Synopsis: sierra show --band

Example:

> sierra show --band

band:

IMT2000

Note: IMT2000 is band 2100 and WCDMA800 is band 850

Connection status

Description: Display the 3G network connection status

Synopsis: sierra show –link

sierra show --gstatus

Examples:

> sierra show --link

link: Connected

> sierra show --gstatus

Current Time:

450

Temperature: 45

Bootup Time:

1

Mode:

ONLINE

System mode:

WCDMA

PS state:

Attached

WCDMA band:

WCDMA800

GSM band:

Unknown

WCDMA channel: 4436

GSM channel: 65535

GMM (PS) state:REGISTERED

NORMAL SERVICE

MM (CS) state: IDLE

NORMAL SERVICE

WCDMA L1 State:L1M_FACH

RRC State:

CELL_FACH

RX level (dBm):-90

Downloaded from

www.Manualslib.com

manuals search engine

Page 74 / 86

74 – YML902

IMSI & IMEI read

Description: Display the IMSI and IMEI value

Synopsis: sierra show --imsi

sierra show --imei

Example:

> sierra show --imsi

imsi: 466974800524867

> sierra show --imei

IMEI: 354219010024303

Wireless LAN mode set and read

Description: Allows user to conﬁgure the Wireless LAN interfaces on the 3G router.

This command can be use to conﬁgure basic feature, security feature, wireless bridge feature and MAC ﬁlter

features of the wireless LAN interface.

Synopsis:

> wlan

wlan command usage :

wlan conﬁg [option]

wlan security [option]

wlan macﬁlter [option]

wlan wds [option]

wlan info [option]

wlan –help

Each option will be explained separately below.

Note:

The settings changed from these commands take effect immediately and will be updated on the web page

1. Please enable the wireless BEFORE changing other wireless settings.

2. The wlan command will save the conﬁguration into ﬂash memory and the new settings will be saved.

Since the settings changed from wlan command take effect immediately, it is not recommended to modify the wireless settings

through the Web UI at the same time.

Downloaded from

www.Manualslib.com

manuals search engine

Page 75 / 86

3G9W - HSPA 7.2Mbps Wi-Fi Router USER GUIDE

YML902 – 75

Conﬁgure basic Wireless LAN features

Description: Conﬁgure basic wireless LAN features such as enable or disable the wireless LAN

interface, hide the network from active scans, set the wireless network name (also known as

SSID) and restrict the channel set based on country requirements.

Synopsis:

wlan conﬁg [--enable <0|1>] [--hide <0|1>]

[--ssid <ssidStr>] [--country <countryStr>]

[--isolate <0|1>]

[--channel <channelVal>] [--rate <rateVal>]

[--mrate <rateVal>]

[--rts <rtsThreshold>] [--frag <fragThreshold>]

[--dtim <dtimInterval>] [--beacon <beaconInterval>]

[--xpress <on|off>] [--gmode <auto|performance|lrs|802.11b>]

[--gprotect <off|auto>] [--preamble <long|short>]

Options:

--enable <0|1>

Description: Enable or disable wireless LAN interface.

Valid value: 0 or 1

0 – disabled the wireless LAN interface.

1 – enabled the wireless LAN interface.

Default value: 1

--hide <0|1>

Description: Hide wireless LAN network name (SSID).

Valid value: 0 or 1

0 – not hide wireless LAN SSID.

1 – hide wireless LAN SSID

Default value: 0

--ssid <ssidStr>

Description: Set Wireless LAN network name (SSID).

Valid value: 32 characters string

--country <countryStr>

Description: Set Wireless LAN Country, only accept abbreviation.

Valid value: 2 or 3 characters string (AUSTRALIA is abbreviated to AU).

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular NetComm Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share