Page 11 / 91
Scroll up to view Page 6 - 10
BigPond Elite™ Wireless Broadband Network Gateway USER GUIDE
11
±.1
SETUP PROCEDURE (WITH USB KEY)
These steps explain how to quickly setup your Next G™ Gateway:
1:
Insert your SIM card (until you hear a click) into t he USIM slot on t he rear of t he Gateway.
±:
Connect t he yellow Et hernet cable to one of t he yellow LAN ports found at t he back of t he
Gateway.
3:
Connect
t he
ot her
end
of
t he
yellow
networking
cable
to
t he
Et hernet
port
on
your
computer.
4:
Connect t he power adapter to t he Power socket on t he back of t he Gateway.
5:
Plug
t he
power
adapter
into
a
wall
socket
and
press
t he
power
button
into
t he
ON
position.
6:
Configure t he Gateway t hrough t he Web User Interface (WUI).
NOTE:
Chapters 4 t hrough 8 explain how to set up and use t he WUI
7:
Save t he Gateway configuration and reboot (see section 7.13).
QUICK SETUP
Page 13 / 91
BigPond Elite™ Wireless Broadband Network Gateway USER GUIDE
13
3.1
SETUP PROCEDURE (WITHOUT USB KEY)
These steps explain how to quickly setup your Next G™ Gateway:
1:
Insert your SIM card (until you hear a click) into t he USIM slot on t he rear of t he Gateway.
±:
Connect t he yellow Et hernet cable to one of t he yellow LAN ports found at t he back of t he
Gateway.
3:
Connect
t he
ot her
end
of
t he
yellow
networking
cable
to
t he
Et hernet
port
on
your
computer.
4:
Connect t he power adapter to t he Power socket on t he back of t he Gateway.
5:
Plug t he power adapter into a wall socket and press t he power button into t he ON position
(depressed).
6:
Configure t he Gateway t hrough t he Web User Interface (WUI).
NOTE:
Chapters 4 t hrough 8 explain how to set up and use t he WUI
7:
Save t he Gateway configuration and reboot (see section 7.13).
3.±
TCP/IP SETTINGS
It is likely t hat your computer will automatically obtain an IP Address and join t he network.
This
is
because
t he
Dynamic
Host
Configuration
Protocol
(DHCP)
server
(on
t he
device)
will
start automatically when your Gateway powers up.
This
automatic
assignment
requires
t hat
DHCP
is
configured
on
your
computers.
It
is
likely
t hat
t his
is
already
t he
case,
but
should
you
be
required
to
configure
t his,
please
see
t he
instructions on t he following page.
ADVANCED SETUP
Page 14 / 91
BigPond Elite™ Wireless Broadband Network Gateway USER GUIDE
14
W I N D O W S
X P
To access t he dialog box t hat allows you to configure your network connection, click on Start >
Control Panel > Network Connections. Then right mouse click on t he Local Area Connection and
select Properties. Select Internet Protocol (TCP/IP) t hen select Properties
DHCP MODE
You can set your PC to DHCP mode by selecting Obtain an IP address automatically in t he dialog
box shown below.
Page 15 / 91
BigPond Elite™ Wireless Broadband Network Gateway USER GUIDE
15
STATIC IP MODE
The following steps show how to assign a Static IP address to your PC using subnet 10.0.0.x.
1:
Change
t he
IP
address
to
t he
domain
of
10.0.0.x.
(1<x<±54)
wit h
subnet
mask
of
±55.±55.±55.0.
±:
Set t he default gateway and DNS server to t he gateway’s IP address.
NOTE:
The IP address of t he gateway is
10.0.0.138. (Default), so t he PC must be set wit h a different IP. In
t he case below, t he PC’s IP address is set as 10.0.0.±
3:
Click Ok to submit t he settings.
19216811.live