Page 111 / 116 Scroll up to view Page 106 - 110
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
111
--station
Description:display the list of authenticated wireless stations and their status
Example:
> --wlan info --station
--wlan info --station:not found
Configure Access Control
Description:to list and to configure access control from LAN & WAN.
(1) To set up the access control list.
Synopsis:remoteaccess service [--service <servicename>] <--interface <none|local|remote|both> >
<servicename>:FTP,HTTP,ICMP,TELNET,SSH,TFTP
<none|local|remote|both>:
none:disable the service.
local:enable the service at LAN side only
remote:enable the service at WAN side only
both:enable the service at both LAN and WAN sides.
(2) To add an entry of IP range that to be enable to manage the gateway.Subnet mask of
255.255.255.255 is for a host with the specific IP address.
Synopsis:remoteaccess iprange --add <IP address> <Subnet mask> <none|local|remote|both>
<none|local|remote|both>
none:forbid the IP range to manage the 3G10WVT.
local:permit the IP range to manage the 3G10WVT from LAN side only.
remote:permit the IP range to manage the 3G10WVT from WAN side only.
both:permit the IP range to manage the 3G10WVT from both LAN and WAN.
(3) To delete an entry of IP range that to be enable to manage the gateway.
Synopsis:remoteaccess iprange --remove <IP address> <Subnet mask>
(4)To enable or disable the all the IP ranges defined by command (2).
Synopsis:remoteaccess accesscontrolmode <--enable <0|1> >
Page 112 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
11±
* Argument --enable 1 is to enable the access list;argument --enable 0 is to disable the access
list;.Please note (a) enabling access list mode is only for the case of at least one IP list is created;
(b) after removing the last entry in the table,the access list mode will be disabled automatically.
This is to avoid no IP being on the list when access mode is enabled;it will cause the gateway no
being able to be managed by any IP address.The only solution under this circumstance is to reset
3G10WVTT gateway back to factory default by press the reset button on the back of the gateway
for over 8 seconds.
(5) To display all current settings for remote access.
Synopsis:remoteaccess show
(6) To view the usage of“remoteacesss”command.
Synopsis:remoteaccess –help
config AP mode.
Default value :ap
--restrict <enabled|disabled>
config bridge restrict mode.
Default value :disabled
--rmac1 <MACaddress>
--rmac2 <MACaddress>
--rmac3 <MACaddress>
--rmac4 <MACaddress>
config remote bridge MAC address
NOTE 4:
You should enable the option -“restrict”before setting any restrict MAC address (setting --
rmac1~4) or your restrict MAC address setting will be ignored.
After the version – C40_R01,the wireless driver – 3.91.15.0 supports both BCM4318 and BCM4306;
Version - C39_R02 with the wireless driver - 3.61.13.0 supports only BCM4306;
The behavior of wds is similar to connect two or more AP using a hub,be aware of the IP assignment
to prevent assigning two or more hosts / STAs to the same IP address.You could enable only one
DHCP server in one gateway and disable all other’s to avoid the conflict of the IP assignment.
WDS CLI does NOT support Enable(Scan) mode in Bridge Restrict while WEB does.If you set Bridge
Restrict to Enable(Scan) mode,the CLI will show Bridge Restrict disabled.
Page 113 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
113
EXAMPLE 4:
After example 3, we want to use wds to connect with the other AP which has disabled the DHCP
server (NOTE 4) and has MAC address - 00:12:34:56:78:9a;we can achieve the goal using the
following command.
wlan wds --mode wds --restrict enabled --rmac1 00:12:34:56:78:9a
info:Show the configurations of WLAN interface and the information of stations connected to
this AP.
Options for the info command
wlan info [--config] [--security]
[--macfilter] [--wds] [--station]
--config
list parameters of config command
--security
list parameters of security command
--macfilter
list parameters of macfilter command
--wds
list parameters of wds command
--station
list authenticated wireless stations and their status
NOTE 5:
You can use this command to view your wireless settings;no matter the settings are modified
from web or CLI,the command will show the latest information for you.
Page 114 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
114
EXAMPLE 5:
After example 4,if we forgot our ssid,we can view the ssid with the following command.
wlan info --config
--help:Display usage for WLAN interface.
Scenario 2 to configure AP with OPEN-disabled security:
wlan config --enable 1--ssid“WLAN_TLF”--hannel 8
wlan security open --wep disabled
Scenario 3 to configure AP with Shred-WEP security
wlan config --enable 1--ssid“WLAN_TLF”--hannel 8
wlan security shared --wep enabled --nkey1 1234567890123 --keyidx 1
Scenario 4 to configure AP with 802.1X security
wlan config --enable 1--ssid“WLAN_TLF”--hannel 8
wlan security radius --rasip 172.16.2.199 --raskey“whatever”--wep enabled
Scenario 5 to configure AP with WPA-PSK security
wlan config --enable 1--ssid“WLAN_TLF”--hannel 8
wlan security psk --pskey“123456789”--wpaenc aes
Scenario 6 to configure AP with WPA2 security
wlan config --enable 1--ssid“WLAN_TLF”--hannel 8
wlan security wpa2 --rasip 172.16.2.199 --wlPreauth 1
Page 115 / 116
TELSTRA TURBO 7 WIRELESS GATEWAY (3G10WVT) - USER GUIDE
115

Rate

4.7 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top