Motorola WR850Gv6 Router Manual PDF (Setup & Configuration Guide)

Home

Manuals

Motorola

WR850Gv6

Page 76 / 93 Scroll up to view Page 71 - 75

3-42

SECTION 3, CONFIGURATION

Field

Description

NTP Server List

Table

Lists the current Network Time Protocol (NTP)

servers from which you can choose for

synchronization.

Or, enter the host name or IP address for a

desired Time Server.

Control Panel - UPnP

This screen enables you to enable/disable Universal Plug and Play

(UPnP). This allows an application to smoothly map to the router.

To access the screen, click

Admin Control Panel

UPnP

. Click

Apply

to save your settings or

Clear

to cancel changes.

Field

Description

LAN UPnP

Device

Click to enable this feature. The default is

disabled.

Control Panel - Event Log

The Event Log window enables you to view events (network activity,

when it occurred, and a textual description) that occur on your

wireless network.

To access the screen, click

Admin Control Panel

Event Log

Click

Apply

to save your settings or

Cancel

to cancel changes.

Click to enable the different types of Event Log information to track.

Page 77 / 93

SECTION 4, TROUBLESHOOTING

4-1

Section 4:Troubleshooting

This section details possible solutions to common problems that

might occur in using the router.

If you are unable to locate a solution here, please access our website

www.motorola.com/broadband/networking

for the latest information.

You can also reach us 7 days a week, 24 hours a day at

1-877-466-8646.

Hardware Solutions

My computer is experiencing difficulty connecting to the wireless

network.

Ensure that your router is powered on and that the Wireless LED

is flashing.

Ensure that your wireless adapter (PCI card, Notebook or

Ethernet adapter) is installed correctly and is active.

Ensure that your wireless adapter’s radio signal is enabled.

Review your adapter’s documentation for further instructions.

Ensure that your wireless adapter for your PC and the wireless

router have the same security settings that will allow your

computer to access the wireless network. Also, verify that the

Access Control List (ACL) is not configured to block your PC.

Section 3: Wireless > Security section details how to adjust

security settings.

Ensure that your wireless adapter is within range of your router or

is not behind obstruction, for example metal structures will

interfere with the signal, as will 2.4 GHz cordless phones, and

microwaves.

Ensure that your router’s antenna is connected and that your

PC’s wireless adapter antenna is also connected.

Page 78 / 93

4-2

SECTION 4, TROUBLESHOOTING

My computer is experiencing difficulty in connecting to the router.

Check all of your cabling connections that they are tight and

secured. This includes the cables from the wall to your modem,

between the router and modem, and, if available, from the router

to your PC. Ensure that your LEDs are not lit

Red

or not at all. For

further information about LED descriptions, see Section 1:

Overview.

Ensure that you are using Ethernet cables and not telephone

cables between the router and modem or router and PC. Ethernet

cables use a wider RJ-45 style plug using 8 wires where

telephone style plugs use the smaller RJ-11 style plug using 4 to

6 wires.

The plug on the left is RJ-45; the plug on the right is RJ-11 – use only

RJ-45.

Ensure that your Ethernet adapter is enabled. Check the System

Tray at the bottom right of your display to see an icon that looks

like a monitor.

You can click on this to see the status of

your Ethernet adapter. Also in Control Panel > Network and

Dial-Up Connections, you can examine the state of your Ethernet

adapter.

My broadband modem already uses a built-in router.

Because the two routers will cancel each other out, turning off the

NAT function in the modem will enable access for your router. Refer

to your modem’s documentation for further instructions.

Page 79 / 93

SECTION 4, TROUBLESHOOTING

4-3

Software Solutions

I would like to test to see if my Internet connection is alive.

For this, you will use the

ping

command to test the connection.

Before attempting, ensure that

Obtain an IP address automatically

has been selected in the computer’s settings and that you have an IP

address assigned. Refer to Section 2: Configuration > Configure

Your Computers, for further details.

Open a command prompt by clicking

Start

and

Run

. For

Windows 98 and ME, in the

Open

field, type

command

and press

Enter or OK. For Windows 2000 and XP, type

cmd

. Or, navigate

using your

Start

button to

Programs

Accessories

Command

Prompt

In the Command window, type “ipconfig”.

You should see an IP address for your network adapter:

Ethernet Adapter Local Area Connection:

Connection-specific DNS Suffix.: Example.example.example.com.

IP Address. . . . . . . . . . . . : 192.168.10.1

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . . : 192.168.10.1

In the

Command

window, type

ping

the Router’s IP address

and

press the

Enter

key. Also, there is a good possibility that the

Default Gateway’s IP address is the router’s IP address. You can

verify the router’s IP address on the

Internet

Basic

screen.

If you receive a reply (the first word will be

Reply…

), then

your computer is connected to the router. Proceed to

Step 4

If you do NOT receive a reply, try from a different computer to

verify that the first PC is not the cause of the problem.

In the

Command

window, type

ping

and your ISP’s default

gateway and press the

Enter

key.

If you receive a reply (It might look something like this:

from 216.109.125.72…

), then your connection to the internet

is alive and well. You can verify the ISP’s IP address at the

Default Gateway field on the

Internet

Basic

screen.

If you do NOT receive a reply, try from a different computer to

verify that the first PC is not the cause of the problem.

Page 80 / 93

4-4

SECTION 4, TROUBLESHOOTING

I cannot access the Configuration Utility for the router.

Verify your Ethernet connection to the router.

Verify that the IP address of the PC being used to configure the

router is on the same network as the router’s configuration IP

address.

The IP address of your network adapter must be on the same

network and not a duplicate of any others on the network (for

example: 192.168.10.3 and using a subnet mask of

255.255.255.0 can be used to login to the router’s default IP

address of 192.168.10.1). Refer to Section 2: Configuration >

Configure Your Computers on how to adjust the IP address for

your PC.

Verify that you can ping the router on this IP address.

In the

Command

window, type

ping

and your router’s default

IP address and press

Enter

If you have changed the factory configured default IP address

of the router, you will need to set your network adapter

accordingly.

Verify you are entering the correct URL in the browser. The

default is

http://192.168.10.1

. If you think you have changed the

IP address used to configure the router and cannot remember it,

you must reset the unit back to factory defaults. To do this, press

and hold the reset button for more the 5 seconds. This clears the

router’s user settings, including User ID, Password, IP Address,

and Subnet mask.

Once the router is reset to factory default, re-verify the Ethernet

connectivity and IP address issues.

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share