1. Home
    2. /
  2. Manuals
    3. /
  3. Motorola
    4. /
  4. SVG1501ES
    5. /
  5. 13
Page 61 / 83 Scroll up to view Page 56 - 60
B
9 • Wireless Pages
51
Field
Description
Afterburner™ Technology
Enhances Wi-Fi 802.11g standard by increasing throughput by
40 percent.
Rate
Forces the transmission rate for the AP to a particular speed.
“Auto” provides best performance in nearly all situations.
Output Power
Sets the output power as a percentage of the hardware’s
maximum capability.
Beacon Interval
Sets the beacon interval for the AP. The default is 100, which
is fine for nearly all applications.
DTIM Interval
Sets the wakeup interval for clients in Power Save mode.
When a client is running in Power Save mode, Lower
SVG1501 bin values provide higher performance but result in
decreased client battery life; higher values provide lower
performance but increased client battery life.
Fragmentation Threshold
Sets the fragmentation threshold. Packets exceeding this
threshold are fragmented into packets smaller than the
threshold before packet transmission.
RTS Threshold
Sets the RTS threshold. Packets exceeding this threshold
cause the AP to perform an RTS/CTS exchange to reserve the
wireless medium before packet transmission.
Page 62 / 83
B
9 • Wireless Pages
52
Wireless 802.11 Access Control Page
Configure the Access Control to the AP and status on the connected clients.
Field Descriptions for the Wireless 802.11 Access Control Page
Field
Description
Wireless Interface
Shows the MAC address of the installed wireless card. It is not
configurable.
MAC Restrict Mode
Selects whether wireless clients with the specified MAC
address are allowed or denied wireless access.
Select
Disabled
to allow all clients.
MAC Address
Lists wireless client MAC addresses allowed or denied
wireless access based on the Restrict Mode setting. Valid input
MAC address formats are XX:XX:XX:XX:XX:XX and XX-XX-XX-
XX-XX-XX.
Connected Clients
Lists connected wireless clients. As a client connects or leaves
the network, it is added to or removed from the list, Age is the
amount of time since data was transmitted to or received from
the client.
Page 63 / 83
B
9 • Wireless Pages
53
Wireless 802.11 Wi-Fi Multimedia Page
Configure the Wi-Fi Multimedia Quality of Service (QoS).
Field Descriptions for the Wireless 802.11 Wi-Fi Multimedia Page
Field
Description
WMM Support
Sets WMM support to Auto, On, or Off.
If enabled (Auto or on), WME Information Element is included
in beacon frames.
No-Acknowledgement
Sets No-Acknowledgement support to On or Off.
When On, acknowledgments for data are not transmitted.
Power Save Support
Sets Power Save support to On or Off.
When On, the AP queues packets for STAs that are in Power
Save mode. Queued packets are transmitted when the STA
notifies the AP that it has left Power Save mode.
EDCA AP Parameters
Specifies the parameters for traffic transmitted from the AP to
the STA in four Access Categories:
•
Best Effort (AC_BE)
•
Background (AC_BK)
•
Video (AC_VI)
•
Voice (AC_VO)
Admission control specifies if it is to be enforced for the
Access Categories.
Discard Oldest First specifies the discard policy for the queues.
“
On” discards oldest first; “Off” discards newest first.
EDCA STA Parameters
Specifies the transmit parameters for traffic transmitted from
the STA to the AP in the four Access Categories.
Page 64 / 83
B
9 • Wireless Pages
54
Wireless 802.11 Bridging Page
Enable wireless bridging.
Field Descriptions for the Wireless 802.11 Bridging Page
Field
Description
Wireless Bridging
Enable or disable wireless bridging.
Remote Bridges
Build a table of remote bridge MAC addresses authorized to
establish a wireless bridge. You can connect up to four remote
bridges. Typically, you must enter your AP’s MAC address on the
remote bridge.
Page 65 / 83
B
9 • Wireless Pages
55
Setting Up Your Wireless LAN
You can use the SVG1501 as an access point for a wireless LAN (WLAN) without
changing the default settings.
CAUTION:
Prevent unauthorized eavesdropping or access by enabling
wireless security after your
WLAN is operational. The default settings
provide no wireless security.
To enable security for your WLAN:
•
Encrypt wireless LAN transmissions
•
Restrict wireless LAN access to further prevent unauthorized WLAN intrusions using
the
Wireless 802.11 Access Control Page
CAUTION:
Never provide your SSID, WPA or WEP passphrase, or WEP
key to anyone who is not authorized to use your WLAN.
Do not attempt to configure the SVG1501 over a wireless connection.
Connect at least one computer to the SVG1501 Ethernet port.
Configure each wireless client (station) to access the SVG1501.
Place wireless components away from windows. This decreases signal strength outside
the intended area.
Encrypting Wireless LAN Transmissions
To prevent unauthorized viewing of data transmitted over your WLAN, you must encrypt
your wireless transmissions. Choose one of the following:
Encrypting Wireless LAN Transmissions
Configure on the SVG1501
Required on Each Wireless Client
If all of your wireless clients support
Wi-Fi Protected Access (WPA),
Motorola recommends configuring
WPA on the SVG1501
If you use a local pre-shared key (WPA-PSK)
passphrase, you must configure the identical
passphrase on the SVG1501 and on each wireless
client. Home and small-office settings typically use a
local passphrase.
Otherwise, configure WEP on the
SVG1501
You must configure the identical WEP key on the
SVG1501 and on each wireless client.

Rate

4 / 5 based on 1 vote.

Popular Motorola Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top