Motorola 3347-02 Router Manual PDF (Setup & Configuration Guide)

Page 301 / 351 Scroll up to view Page 296 - 300

301

CONFIG Commands

set voip phone: 1 sip-advanced-setting sip-dtmf-mode rfc2833

set voip phone: 1 sip-advanced-setting sip-end-of-dial-marker off

set voip phone: 1 sip-advanced-setting call-feature call-forwarding-all-

option off

set voip phone: 1 sip-advanced-setting call-feature call-forwarding-on-busy-

option off

set voip phone: 1 sip-advanced-setting call-feature call-forwarding-on-no-

answer-option off

set voip phone: 1 sip-advanced-setting call-feature call-waiting-option off

set voip phone: 1 sip-advanced-setting call-feature call-conferencing-option

off

set voip phone: 1 sip-advanced-setting call-feature subscribe-do-not-

disturb-option off

set voip phone: 1 sip-advanced-setting call-feature subscribe-mwi-option off

set voip phone: 1 sip-advanced-setting dsp-settings echo-option echo-on-cng-

nlp

set voip phone: 1 sip-advanced-setting dsp-settings echo-start-attenuation

8192

set voip phone: 1 sip-advanced-setting dsp-settings echo-max-attenuation

16384

set voip phone: 1 sip-advanced-setting dsp-settings echo-tail-length 0

set voip phone: 1 sip-advanced-setting dsp-settings vad-option off

UPnP settings

set upnp option [ on | off ]

PCs using UPnP can retrieve the Gateway’s WAN IP address, and automatically create NAT

port maps. This means that applications that support UPnP, and are used with a UPnP-

enabled Motorola Netopia® Gateway, will not need application layer gateway support on

the Motorola Netopia® Gateway to work through NAT. The default is

on

.

You can disable UPnP, if you are not using any UPnP devices or applications.

set upnp log [ off | on ]

Enables or disables UPnP logging.

set upnp read-only [ off | on ]

Enables or disables

Page 302 / 351

302

DSL Forum settings

TR-064 is a LAN-side DSL CPE conﬁguration speciﬁcation and TR-069 is a WAN-side DSL

CPE Management speciﬁcation.

TR-064

DSL Forum LAN Side CPE Conﬁguration (TR-064) is an extension of UPnP. It deﬁnes more

services to locally manage the Motorola Netopia® Gateway. While UPnP allows open

access to conﬁgure the Gateway's features, TR-064 requires a password to execute any

command that changes the Gateway's conﬁguration.

set dslf-lanmgmt option [ off | on ]

Turns TR-064 LAN side management services on or off. The default is

on

.

TR-069

DSL Forum CPE WAN Management Protocol (TR-069) provides services similar to UPnP and

TR-064. The communication between the Motorola Netopia® Gateway and management

agent in UPnP and TR-064 is strictly over the LAN, whereas the communication in TR-069 is

over the WAN link for some features and over the LAN for others. TR-069 allows a remote

Auto-Conﬁg Server (ACS) to provision and manage the Motorola Netopia® Gateway. TR-069

protects sensitive data on the Gateway by not advertising its presence, and by password

protection.

set dslf-cpewan option [ off | on ]

set dslf-cpewan acs-url "

acs_url:port_number

"

set dslf-cpewan acs-user-name “

acs_username

”

set dslf-cpewan acs-user-password “

acs_password

”

Turns TR-069 WAN side management services on or off. For 3300-Series Gateways, the

default is

off

; for 2200-Series Gateways, the default is

on

. If TR-069 WAN side manage-

ment services are enabled, speciﬁes the auto-conﬁg server URL and port number. A user-

name and password must also be supplied, if TR-069 is enabled.

Page 303 / 351

303

CONFIG Commands

The auto-conﬁg server is speciﬁed by URL and port number. The format for the ACS URL is

as follows:

http://

some_url.com

:

port_number

or

http://

123.45.678.910

:

port_number

On units that support SSL, the format for the ACS URL can also be:

https://

some_url.com

:

port_number

or

https://

123.45.678.910

:

port_number

Page 304 / 351

304

Backup IP Gateway Settings

The purpose of Backup is to provide a recovery mechanism in the event that the primary

connection fails. A failure can be either line loss, for example by central site switch failure

or physical cable breakage, or loss of end-to-end connectivity. Detection of one of these

failures causes the Gateway to switch from using the primary DSL WAN connection to an

alternate gateway on the Ethernet LAN. In the event of a loss of primary connectivity you

have the option of switching back to the primary circuit automatically once it has recovered

its connection.

A typical application would be to have a LAN connection from your Gateway to another

Gateway that has, for example, another DSL modem or Gateway connection to the Internet,

and designating the second gateway as the backup gateway. Should the primary WAN

connection fail, trafﬁc would be automatically redirected through your alternate gateway

device to maintain Internet connectivity.

set backup option [ disabled | manual | automatic ]

Speciﬁes whether backup to an IP gateway is

disabled

or enabled as

manual

or

auto-

matic

. Default is

disabled

.

set backup failure-timeout [ 1 - 10 ]

Speciﬁes the number of minutes you want the system to wait before the backup port

becomes enabled in the event of primary line failure, when

backup option

is set to

auto-

matic

. Sets the Default is

1

.

set backup ping-host [ 1 | 2 ] [ name | address ]

Speciﬁes whether the Gateway will ping an IP address or resolvable DNS name, when

backup option

is set to

automatic

. These are optional items that are particularly useful

for testing if the remote end of a VPN connection has gone down.

The Gateway will ping both addresses simultaneously at ﬁve-second intervals, recording

the ping responses from each host. The Gateway will proceed into backup mode only if nei-

ther of the conﬁgured remote hosts responds.

Page 305 / 351

305

CONFIG Commands

set backup ping-host [ 1 | 2 ] [ name

hostname

| ip-address

ip_address

]

Speciﬁes an IP address or resolvable DNS name for the Gateway to ping.

set backup auto-recovery [ off | on ]

Turns automatic recovery

off

or

on

. Default is

off

.

set backup recovery-timeout [ 1 - 10 ]

If

auto-recovery

is set to

on

, speciﬁes the number of minutes for the system to wait

before attempting to switch back to the WAN connection. This allows you to be sure that

the WAN connection is well re-established before the gateway switches back to it from the

backup mode. Default is

1

.

set ip backup-gateway option [ on | off ]

Turns the backup gateway option

on

or

off

. Default is

off

.

set ip backup-gateway interface ip-address

Speciﬁes the backup gateway interface ip address to which you want to direct the backup

connection.

set ip backup-gateway default

ip_address

Speciﬁes the ip address of the default gateway.

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share