Motorola 3347 Qwest Router Manual PDF (Setup & Configuration Guide)

Page 246 / 351 Scroll up to view Page 241 - 245

246

PPPoE with IPoE Settings

Ethernet WAN platforms

set wan-over-ether pppoe [ on | off ]

Enables or disables PPPoE on the Ethernet WAN interface.

set wan-over-ether pppoe-with-ipoe [ on | off ]

Enables or disables the PPPoE with IPoE support on Ethernet WAN, including VDSL, plat-

forms when

pppoe

option

is set to

on

.

When

pppoe-with-ipoe

is set to

on

, an additional interface, “ethernet C,” becomes avail-

able.

set wan-over-ether ipoe-sessions [ 1 - 4 ]

Sets the number of IPoE sessions, up to four, on Ethernet WAN, including VDSL, platforms.

☛

NOTE:

Enabling pppoe-with-ipoe disables support for multiple PPPoE sessions.

Example:

set ip ethernet C option on

set ip ethernet C address 0.0.0.0

set ip ethernet C broadcast 0.0.0.255

set ip ethernet C netmask 255.255.255.0

set ip ethernet C restrictions admin-disabled

set ip ethernet C addr-mapping on

set ip ethernet C dns acquired-dns-priority 20

set ip ethernet C mcast-fwd on

set ip ethernet C igmp-null-source-addr off

set ip ethernet C tx-queue "none"

set ip ethernet C unnumbered off

set ip ethernet C rip-receive off

set ip ethernet C proxy-arp off

Page 247 / 351

247

CONFIG Commands

set ip ip-ppp enet-B option on

set ip ip-ppp enet-B address 0.0.0.0

set ip ip-ppp enet-B peer-address 0.0.0.0

set ip ip-ppp enet-B restrictions admin-disabled

set ip ip-ppp enet-B addr-mapping on

set ip ip-ppp enet-B dns acquired-dns-priority 20

set ip ip-ppp enet-B igmp-null-source-addr off

set ip ip-ppp enet-B tx-queue "none"

set ip ip-ppp enet-B mcast-fwd on

set ip ip-ppp enet-B unnumbered off

set ip ip-ppp enet-B rip-receive off

ADSL platforms

You must conﬁgure two VCCs with the

same

VPI/VCI to enable concurrent PPPoE and IPoE

support, and you will need to conﬁgure the individual settings for each interface for proper

operation.

set atm vcc

n

encap pppoe-llc

Speciﬁes that the VCC will allow a second VCC with the same VPI/VCI values as the ﬁrst.

pppoe-llc

denotes this special case.

Example:

set atm option on

set atm vcc 1 option on

set atm vcc 1 vpi 0

set atm vcc 1 vci 35

set atm vcc 1 encap pppoe-llc

set atm vcc 2 option on

set atm vcc 2 vpi 0

set atm vcc 2 vci 35

set atm vcc 2 encap ether-llc

This will allow you to conﬁgure the second WAN interface.

set atm vcc 2 vpi 0

set atm vcc 2 vci 35

set atm vcc 2 encap ether-llc

...

Page 248 / 351

248

set ip ip-ppp vcc1 mcast-fwd [ on | off }

Enables or disables multi-cast forwarding on the speciﬁed interface. If set to

on

, this inter-

face acts as an IGMP proxy host, and IGMP packets are transmitted and received on this

interface on behalf of IGMP hosts on the LAN interface. See

“

IGMP Settings

” on page

211

for more information.

set ip ip-ppp vcc1 igmp-null-source-addr [ off | on ]

Enables or disables IGMP null source address, if

mcast-fwd

is set to

on

. If enabled, the

source IP address of every IGMP packet transmitted from this interface is set to 0.0.0.0.

This complies with the requirements of TR-101, and removes the need for a publicly adver-

tised IP address on the WAN interface.

Ethernet Port Settings

set ethernet ethernet A mode { auto | 100M-full | 100M-full-ﬁxed |

100M-half-ﬁxed | 10M-full-ﬁxed | 10M-half-ﬁxed |

100M-half | 10M-full | 10M-half }

Allows mode setting for the ethernet port. Only supported on units without a LAN switch, or

dual ethernet products (338x). In the dual ethernet case, “ethernet B” would be speciﬁed

for the WAN port. The default is

auto

.

Page 249 / 351

249

CONFIG Commands

802.3ah Ethernet OAM Settings

802.3ah Ethernet in the First Mile (EFM) Operations Administration and Maintenance

(OAM) is a group of network management functions that provide network fault indication,

performance information, and diagnosis using special-purpose Ethernet OAM frames.

These are exchanged between your Gateway and service provider Access Node (AN)

devices for network fault management, performance analysis and fault isolation.

All VDSL and Ethernet WAN Motorola Netopia Gateways support Ethernet OAM options.

More Ethernet Packet-Transfer-Mode (PTM) enabled xDSL Motorola Netopia Gateways will

support 802.3ah Ethernet OAM options in future releases.

802.3ah Ethernet OAM exchanges periodic Ethernet OAM heartbeat frames between the

endpoints of the physical link being monitored, and thus discovers and keeps-alive the Link

connectivity and reports faults if the link goes down. Supported OAM request and

response types are: remote loopback enable, remote loopback disable, variable request,

variable response.

set ethernet oam ah option [ off | on ]

Enables or disables Ethernet OAM. Default is

off

.

set ethernet oam ah pass-through [ off | on ]

Enable or disable Ethernet OAM pass-through mode. Default is

off

.

Warning

: This is a DEBUG feature. Leave it off unless you know exactly what you are

doing.

set ethernet oam ah mode [ active | passive ]

Speciﬁes the Ethernet OAM mode. Default is

active

.

set ethernet oam ah pdu-size-max [ 64 - 1518 ]

Speciﬁes the Maximum Protocol Data Unit (PDU) size. Default is

1518

.

Page 250 / 351

250

set ethernet oam ah discovery-timer [ 1 - 300 ]

Speciﬁes the discovery timer value for continuity check in seconds. Range is 1 – 300 sec-

onds. Default is

1

.

set ethernet oam ah keepalive-timer [ 5 - 305 ]

Speciﬁes the keep-alive timer value in seconds. Range is 5 – 305 seconds. Default is

5

.

etheroam ah ping

Sends OAM remote loopback request in active mode.

Rate

Popular Motorola Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share