1. Home
    2. /
  2. Manuals
    3. /
  3. MoFi
    4. /
  4. MOFI3500-3GN
    5. /
  5. 10
Page 46 / 57 Scroll up to view Page 41 - 45
User Manual v2.0
Page 46
of 57
1. If your hotspot or other router that you want to get the
internet from has as the ip address range of
192.168.0.something, then you need to do the following 2
steps, if not go to step 3.
Note that most devices such as the wifi hotspot do not
have this address so most likely you can skip this.
Go to "Network -> Interfaces -> LAN" and and set the IP
address subnet to something other than the ip range of
the origin router.
(example, if the original router is 192.168.0.1, then you
have to change the setting on this router such as to
192.168.1.1, but both router cannot have same ip
address)
2. If you had to change the router ip address, Select the
"Save and Apply" button. Since you just changed the IP
of the router, you will need to re-connect your PC to the
router (DHCP). Close your browser and wait for a few
Page 47 / 57
User Manual v2.5
Page 47
of 57
mins then reopen browser again.
You can also speed this up by taking out the network jack
at back of the router and put it in another one of the 4
ports. Else worst case, just reboot your pc.
After your PC has received a new IP address, enter the
router's new IP address in your web browser and re-login
to the router using the new ip you selected.
If you changed the router ip for example to 192.168.1.1,
then you need to enter this in order to log into the router.
If you make a mistake and loose connection to the router,
you can reset the router by hold down the reset button in
the back (next to the USB port) for 10 seconds while the
power is on the router. After you release the button, the
router will reset back to the default address 192.168.0.1
3. Go to "Network -> Wifi" and select "Find and Join
Network" (icon with magnifying glass on far right). This
scans for available SSIDs (wireless networks)
Page 48 / 57
User Manual v2.0
Page 48
of 57
4. Find the network you wish to join (repeat scan if
necessary) and select the "Join Network" button (this
starts the Join Network wizard).
5. Enter the wireless encryption key (WPA passphrase,
WEP key, etc) of the network you are joining.
Leave the other fields at the default settings (network =
wwan, firewall-zone = wan) and select the "Submit"
button. Then click on "Save & Apply" and wait for to
save.
6. Note that some changes have not been applied yet, but
the configuration has been setup accordingly ("Unsaved
Changes: xx").
It may ask you to log in, just click on log on.
Select the "Save and Apply" button and wait a few
seconds for changes to apply (note the "Applying
Changes" box). Changes should reflect zero ("Changes:
0").
Page 49 / 57
User Manual v2.5
Page 49
of 57
At this point your wireless bridge should be setup. The
WLAN LED should be on. Go to "Network -> Interfaces"
and make sure the "wwan" interface has an IPV4 address
(this should be in the same subnet as the original router).
Your computer should now have internet access via the
wireless bridge.
You can use this for example to supply internet to
multiple devices connected to the Ethernet port and this
is a great way if you want for example to connect your
DVD Player, TV, or other device to the internet without
having to run network cables in your living room.
Page 50 / 57
User Manual v2.0
Page 50
of 57
How to do a firmware upgrade:
Go to www.mofinetwork.com
Click the support then download section to get the latest firmware
Save the firmware file to your desktop
To do the firmware update, you must connect to the router with a network cable from your pc
to the router.
Take out the 3G\4G\LTE stick from the back of the router
You cannot do this update on wireless
1) Take the stick out of your router
2) Power on router and connect to port 1 on the back of the router
3) Connect the network cable to your pc (you cannot do the update via wireless, must use
network cable)
Disconnect your wireless network if you are connected to one,
4) After router is completed booting up (takes approx 60 seconds), open up your internet
explorer or firefox (do not use Google Chrome)
5) In the address bar, enter
username: root
password: admin
6) Click on System Tab on top or if you are in basic mode, click on advance or administrative
mode and then click on the system tab
7) Click on Flash Firmware Tab
8) Uncheck "Keep configuration files" and click on Browse...
9) Locate the file that you saved and click on Open
10) Click on "Upload image"
You should see the file size as well as a checksum
Verify that the file size and checksum is correct from what you get when you downloaded the
latest firmware off the Mofi's site.
11) Click "Proceed" to start the update process

Rate

3.5 / 5 based on 2 votes.

Popular MoFi Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top