1. Home
    2. /
  2. Manuals
    3. /
  3. Luxul
    4. /
  4. XBR-2300
    5. /
  5. 4
Page 16 / 52 Scroll up to view Page 11 - 15
User Guide
16
© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
NOTE:
1.
If the default IP address has been changed, the new IP address
must be entered into the XenSmart management interface.
The default gateway value of all devices connected to the
LAN must be set to the new IP address in order to have
Internet access.
2.
If your client device is set to use DHCP, the address must be
re-requested. This can be done by simply unplugging and
re-plugging the Ethernet cable.
5.3.2 WAN Settings
This interface displays the status of the WAN connections, as well as the port
parameters.
To change the WAN interface settings, select “Edit” next to the WAN interface you
would like to change. This opens up the interface shown below.
Each WAN interface supports three connection modes: Static IP, Dynamic IP and
PPPoE dial-up.
±
Static IP:
w
IP Address: Enter the Static WAN IP Address. If unknown, contact your ISP.
Page 17 / 52
luxul.com
|
357 South 670 West
|
Suite 160
|
Lindon, UT 84042
|
p: 801-822-5450
|
f: 801-822-5460
User Guide
17
w
Subnet Mask: Enter the Static WAN Subnet Mask. If unknown, contact your ISP.
w
Default Gateway: Enter the Static Gateway that corresponds with IP and is
provided by your ISP. If unknown, contact your ISP.
w
Preferred DNS Server/ Alternate DNS server: Enter the DNS server IP address
provided by your ISP. If unknown, contact your ISP.
w
Upstream/Downstream Bandwidth (Optional): Enter the static upstream/down-
stream bandwidth for WAN port1. If unsure of Bandwidths, contact your ISP.
w
MTU Setting: MTU (Maximum Transmission Unit) System default is 1450 bytes.
NOTE:
Typically there is no need to change this. Improper MTU
configuration may lead to poor network performance.
±
Dynamic IP:
If the access mode is Dynamic IP, the XBR-2300 will obtain an IP
address automatically from your ISP.
w
Upstream/Downstream Bandwidth (Optional): Set the static upstream/
downstream bandwidth for WAN port1. If you are not sure of the Bandwidths,
contact your local ISP.
w
MTU: MTU (Maximum Transmission Unit). System default is 1450 bytes.
NOTE:
Typically there is no need to change this. Improper MTU
configuration may lead to poor network performance.
±
PPPoE:
If the access mode is PPPoE, the XBR-2300 will obtain an IP address via
DSL virtual dial-up.
Page 18 / 52
User Guide
18
© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
w
PPPoE Account: Enter the PPPoE account name. If not sure of your Account
Name, please contact your local ISP.
w
PPPOE Password: PPPoE password provided by your ISP. If not sure of your
Password, please contact your local ISP.
w
Upstream/Downstream Bandwidth (Optional): Enter the PPPoE upstream/
downstream bandwidth for WAN1. If not sure of your Bandwidths, please
contact your ISP.
w
MTU: MTU (Maximum Transmission Unit) System default is 1450 bytes.
NOTE:
Typically there is no need to change this. Improper MTU
configuration may lead to poor network performance.
±
PPTP:
If the connection is PPTP, your ISP should provide information to set the
following parameters. PPTP can be Dynamic or Static:
w
PPTP Server IP Address: IP Address of the ISPs PPTP server. If you are not sure of
the PPTP Server IP, contact your ISP.
w
User Name: Enter your PPTP user name. If not sure of your User Name, contact
your ISP.
w
PPTP Password: PPTP Password provided by your ISP. If not sure of your
Password, contact your ISP.
w
Address Mode: There are two modes available:
•
Dynamic IP: With Dynamic, the IP Address, Subnet Mask and Default
Gateway will be automatically configured for you.
•
Static IP: With Static IP, your ISP will need to provide you with your IP
Address, Subnet Mask and Default Gateway. If not sure of your IP Address,
Subnet Mask and Default Gateway, contact your ISP.
NOTE:
When the IP Mode is set to Dynamic, no configuration is needed
for the next three settings, IP Address, Subnet Mask and Default
Gateway.
w
IP Address: The IP Address assigned by your ISP.
w
Subnet Mask: The Subnet Mask assigned by your ISP.
w
Default Gateway: The Default Gateway assigned by your ISP.
w
Upstream/Downstream Bandwidth: The PPTP upstream/downstream band-
width for WAN1. If not sure of your Bandwidths, contact your ISP.
w
MTU: MTU (Maximum Transmission Unit). System default is 1450 bytes.
NOTE:
Typically there is no need to change this. Improper MTU
configuration may lead to poor network performance.
Page 19 / 52
luxul.com
|
357 South 670 West
|
Suite 160
|
Lindon, UT 84042
|
p: 801-822-5450
|
f: 801-822-5460
User Guide
19
w
MPPE: Enables support for Microsoft’s MPPE stateful encryption.
NOTE:
If you experience moderate to high packet loss, do not enable
this function.
±
L2TP:
If the ISP connection is L2TP, you will need to input the following param-
eters provided by your ISP. L2TP can be Dynamic or Static:
w
L2TP Server IP Address: IP Address of your ISPs L2TP server. If not sure of your
PPTP Server IP, contact your ISP.
w
User Name: Enter your L2TP User Name. If not sure of your User Name, contact
your ISP.
w
L2TP Password: L2TP password provided by your ISP. If not sure of your
Password, contact your ISP.
w
Address Mode: There are two modes available:
•
Dynamic IP: With Dynamic, the IP Address, Subnet Mask and Default
Gateway will be automatically configured for you.
•
Static IP: With Static IP, your ISP will need to provide you with your IP
Address, Subnet Mask and Default Gateway. If not sure of your IP Address,
Subnet Mask and Default Gateway, contact your ISP.
NOTE:
When the IP Mode is set to Dynamic, no configuration is needed
for the next three settings, IP Address, Subnet Mask and Default
Gateway.
w
IP Address: The IP Address assigned by your ISP.
w
Subnet Mask: The Subnet Mask assigned by your ISP.
w
Default Gateway: The Default Gateway assigned by your ISP.
w
Upstream/Downstream Bandwidth: The PPTP upstream/downstream band-
width for WAN1. If not sure of your Bandwidths, contact your ISP.
w
MTU: MTU (Maximum Transmission Unit). System default is 1450 bytes.
NOTE:
Typically there is no need to change this. Improper MTU
configuration may lead to poor network performance.
NOTE:
The configuration methods for the WAN2 interface are the same
as for WAN1.
5.3.3 Dual-WAN Policy
This function allows you to choose the Dual-WAN Policy that best meets your
needs. Your XBR-2300 has three Active Policies: Automatic Load Balancing, for
Page 20 / 52
User Guide
20
© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
allowing each client access to the maximum available data rate; Automatic Failover,
for redundant links; and IP Groups, for controlling how much bandwidth is given to
each client.
±
Automatic Load Balancing:
The system searches for the WAN port with the
lowest usage and automatically distributes load accordingly. This load balancing
mode automatically manages flow distribution and bandwidth overlap.
NOTE:
The system default mode is Automatic Load Balancing.
±
Automatic Failover:
Users can choose a WAN port (WAN1 or WAN2), as the
primary connection, while making the other port a backup connection. The
XBR-2300 will automatically switch to the backup connection when the primary
connection has an interruption in service. This change over is subject to a short
delay of approximately 40 seconds on primary connection failure.
±
IP Group:
This mode allows for the control of bandwidth provided to groups
of client devices. When using this mode, specific IP address ranges are placed in
groups and assigned to a particular port (WAN1 or WAN2). The source address,
destination address, and destination port are all specified. All data packets
included in the defined range are then processed by the selected WAN interface.
All data packets that are not included in the defined range are forwarded to the
other WAN interface.
Example:
To designate that LAN Source IP addresses with a range of 192.168.0.100
to 192.168.0.200 pass through WAN2 and with a Destination IP Address range of
58.251.80.1 to 58.251.80.254, via ports: 0-65535, you need to fill in the corresponding
source IP Addresses, Destination IP Addresses, Destination Ports, and Designate a
WAN port. To activate this setting, check “Enabled” and click “Add to the corre-
sponding list.” See below for details:

Rate

3.5 / 5 based on 2 votes.

Popular Luxul Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top