1. Home
    2. /
  2. Manuals
    3. /
  3. LogN
    4. /
  4. HN-DR4PG
    5. /
  5. 3
Page 11 / 85 Scroll up to view Page 6 - 10
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
11
3
Getting Started
Before you start, Please make sure you have all the contents in the package and that you meet
the minimum system requirement:
3.1
Package Contents
HN-DR4PG Wireless Modem Router
Power Adapter
1 x RJ-11 Telephone Cable
1 x RJ-45 LAN Cable
Quick Installation Guide
CD
1 x ADSL Splitter (Optional)
3.2
Minimum System Requirements
ADSL Subscription
PC with Ethernet Port and/or Wireless
WiFi Module for non wireless-enabled PCs
Page 12 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
12
3.3
Hardware Installation
1.
Connect one end of the telephone cable to the ADSL port on the ADSL router.
2.
Connect the other end of the telephone cable into the ADSL port of the ADSL splitter or
directly to the wall phone socket.
3.
Connect the ADSL splitter line port to the wall phone socket whereby the ADSL service is
activated.
4.
Connect one end of the LAN cable to the LAN port of the ADSL router.
5.
Connect the other end of the LAN cable to the LAN port of your PC or laptop.
6.
Connect the power adapter to the power socket.
7.
Switch on your ADSL router.
The “Power” LED will start in RED.
8.
Wait until the
“
Power
”
,
“
LAN
”
and
“
ADSL
” L
EDs are lit ON and fixed. The
“
WLAN
”
will be
blinking. The
“
Internet
”
LED will depend on your ISP Internet connection settings.
To connect to the device wirelessly, replace steps 4-5 with:
1.
Switch your PC WiFi radio on
2.
Search for LogN_HN-DR4PG, connect to it.
Page 13 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
13
3.4
Software Quick Configuration
When you power on the device, the system will boot up and connect to ADSL automatically.
The system provides a PVC for bridge test by default. The default configurations for the
system are listed below:
LAN IP address:
192.168.1.1
, NetMask:
255.255.255.0
UART setting: 115200bps, 8 bits, no parity, 1 stop bit, no flow control.
VPI/VCI for ATM:
0/35
ADSL Line mode: Auto-detect.
This is what causes the
“
ADSL
”
LED blink first then lit ON and fixed at the end meaning the
ADSL connection to the ISP is established.
NOTE:
This does not mean that you are connected to the Internet, as this depends on your ISP
Internet connection settings that your ISP should provide. In a special case of ISP Internet
settings, you may get connected to Internet automatically and having the “Internet” LED lit
on.
To set the ISP connection settings via WEB browser, the following sections describe the
quick set up procedures:
1.
Please set your PCs Ethernet port as follow:
IP address:
192.168.1.XXX
(e.g. 192.168.1.10)
NetMask:
255.255.255.0
2.
Start your web browser.
3.
Type the Ethernet IP address of the modem/router on the address bar of the browser.
Default IP address:
192.168.1.1.
4.
Whenever the
“
Enter Network Password
”
dialog box appears, type:
Default Username:
admin
Password:
password
5.
Once you are connected to the modem/router, you will see the
“
ADSL Router Status
” page
.
Make sure that “DSL” status shows information for “Operational Status”, “Upstream Speed”
and “Downstream Speed” like:
Operational Status:
G992.5, SHOWTIME.L0(Interleave)
Upstream Speed:
126 kbps
Downstream Speed:
511 kbps
6.
Click on “Quick Setup”
button. Refer to section
“Quick Setup”
to see description of the
page.
Page 14 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
14
7.
Type the ISP Internet connection User Name and password provided by your ISP.
8.
Save and Reboot.
9.
Wait until “Internet”
LED is constantly ON. The
“
ADSL
”
LED should be ON as well.
10.
If the LEDs are ON, you should be connected to the internet. Start your browser and surf
internet freely.
If these quick setup procedures failed to connect you to the internet, you may have
advanced ADSL connection settings that need more details:
1.
Repeat steps 1-4 of last procedure.
2.
Click on “
Internet Interface
” and select “WAN Configuration”. Refer to section “Internet
Interface” to see description of the page.
3.
Select one of the connections shown in the table. Modify it to exactly meet your ISP
connection settings then press
“Modify”.
4.
Press the “Save” button on the right down part
of the screen.
5.
Wait until “Internet”
LED is constantly
ON. The “ADSL” LED should be ON as well.
6.
If the LEDs are ON, you should be connected to the internet. Start your browser and surf
internet freely.
To c
onfigure more features, Please refer to “Graphical User Interface pages” chapter at
the section of the feature you want to configure.
Page 15 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
15
4
Graphical User Interface Pages
4.1
Status
4.1.1
Status
It
displays the ADSL modem/router’s current status and settings. This information is
read-only except for the PPPoE/PPPoA channel for which user can connect/disconnect the
channel on demand. Click the “Refresh” button to update the status

Rate

4 / 5 based on 3 votes.

Popular LogN Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top