1. Home
    2. /
  2. Manuals
    3. /
  3. LogN
    4. /
  4. HN-DR4PG
    5. /
  5. 8
Page 36 / 85 Scroll up to view Page 31 - 35
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
36
Fields in this page:
Field
Description
Disable C2C
Check to disable the Click to Connect Setup.
C2C Status
When AP’s settings are factory default (out of
box), it is set to open
security and un-
configured state. “
C2C
Status” will display it as
“UnConfigured”. If it already shows “Configured”, some registrars such as
Vista WCN will not configure AP. Users will need to go to the
“Backup/Restore” page and click “Reset” to reload factory default
settings.
Self-PIN Number
“Self
-
PIN Number” is AP’s PIN. Whenever users want to change AP’s PIN,
they could click “Regenerate PIN” and then click “ Apply Changes”.
Moreover, if users want to make their own PIN, they could enter
four-
digit PIN without checksum and then click “ Apply Changes”.
However, this would not be recommended since the registrar side needs
to be supported with four-digit PIN.
Push Button
Configuration
Clicking this button will invoke the PBC method of C2C. It is only used
when AP acts as a registrar.
Client PIN Number
It is only used when users want their station to join AP’s network. The
length of PIN is limited to four or eight numeric digits. If users enter
eight-digit PIN with checksum error, there will be a warning message
Page 37 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
37
popping up. If users insist on this PIN, AP will take it.
Function buttons in this page:
Regenerate PIN
Click to regenerate the Self-PIN Number.
Start PBC
Click to start the Push Button method of WPS.
Apply Changes
Set new configuration. New parameters will take effect after save into flash memory and
reboot the system. See section “Admin” for save details.
Reset
Discard your changes.
Start PIN
Click to start the PIN method of WPS.
4.5
Internet Interface
There are three sub-menus for WAN configuration: [Channel Config], [ATM Settings], and
[ADSL Settings].
4.5.1
WAN Configuration
ADSL modem/router comes with 8 ATM Permanent Virtual Channels (PVCs) at the most.
There are mainly three operations for each of the PVC channels: add, delete and modify. And
there are several channel modes to be selected for each PVC channel. For each of the
channel modes, the setting is quite different accordingly.
Page 38 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
38
Function buttons in this page:
NEW PVC
Click to add a New PVC, It will add new PVC when the available PVCs shown in the table are
less than 8.
Delete Selected
Select an existing PVC channel to be deleted by clicking the radio button at the
Select
column of the
Current ATM VC Table
. Click
Delete
to delete this PVC channel from
configuration.
ADD
Click
Add
to complete the channel setup and add this PVC channel into configuration.
Modify
Select an existing PVC channel by clicking the radio button at the
Select
column of the
Current ATM VC Table
before we can modify the PVC channel. After selecting an PVC
channel, we can modify the channel configuration at this page. Click
Modify
to complete the
channel modification and apply to the configuration.
ADSL router supports multiple channel operation modes. This section will show procedures
to configure the router.
4.5.1.1
PPPoE Mode
1.
Select the Channel Mode to “PPPoE”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
2.
Enter user/password from your ISP.
3.
Click “Add” button
to add this channel.
4.
Enable DHCP server to allow the local PCs share the PPP connection. Reference to
Page 39 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
39
section DHCP Seetings.
5.
Set DNS address from your ISP. Reference to section DNS.
6.
Open the WEB page at “Admin/Commit/Reboot”. Press “Commit” to save the set
tings
into flash memory.
7.
The new settings will take effect after reboot the system.
4.5.1.2
PPPoA Mode
1.
Select the Channel Mode to “PPPoA”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
2.
Enter user/password from your ISP.
3.
Cl
ick “Add” button to add this channel.
4.
Enable DHCP server to allow the local PCs share the PPP connection. Reference to
section DHCP Settings.
5.
Set DNS address from your ISP. Reference to section DNS.
6.
Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
7.
The new settings will take effect after reboot the system.
4.5.1.3
Bridge Mode
1.
Select your VPI/VCI under ATM VC table
2.
Change the Channel Mode to “1483 Bridged”. Set the parameters VPI/VCI and
Encapsulation mode according
to the CO DSLAM’s setting.
3.
Click “Add” button to add this channel into VC table.
4.
Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
5.
The new settings will take effect after reboot the system.
4.5.1.4
1483 Routed Mode
1.
Select the Channel Mode to “1483 Routed”. Set the parameters VPI/VCI and
Encapsulation mode according to the CO DSLAM’s setting.
2.
In WAN IP settings, give the local and remote IP address from your ISP or use DHCP to
get them automatically if your ISP support it. Local IP is the address of ADSL router.
Remote IP is the ISP’s gateway address.
3.
Click “Add” button to add this channel.
4.
Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
5.
The new settings will take effect after reboot the system.
Page 40 / 85
User Manual
54 Mbps Wireless G Modem Router With 4 Port Switch
HN-DR4PG
40
4.5.1.5
MER(Mac Encapsulating Routing) Mode
1.
Select the Channel Mode to “1483 MER”. Set the parameters VPI/VCI and Encapsulation
mode according to the CO DSLAM’s setting.
2.
Set “Local IP Address:” according to the IP that ISP assign for your router. Set “Remote
IP Address” to the ISP’s gateway.
3.
Click “Add” button to add this channel into VC table.
4.
Open the WEB page at “Admin/ Commit/Reboot”. Press “Commit” to save the settings
into flash memory.
5.
The new settings will take effect after reboot the system.
4.5.2
ATM Setting
The page is for ATM PVC QoS parameters setting. The DSL device support 4 QoS
mode
—
CBR/rt-VBR/nrt-VBR/UBR.
Fields in this page:
Field
Description
VPI
Virtual Path Identifier. This is read-only field and is selected on the
Select
column in the Current ATM VC Table.
VCI
Virtual Channel Identifier. This is read-only field and is selected on the
Select
column in the Current ATM VC Table. The VCI, together with VPI, is used to
identify the next destination of a cell as it passes through to the ATM switch.
QoS
Quality of Server, a characteristic of data transmission that measures how
accurately and how quickly a message or data is transferred from a source host
to a destination host over a network. The four QoS options are:

Rate

4 / 5 based on 3 votes.

Popular LogN Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top