1. Home
    2. /
  2. Manuals
    3. /
  3. Linksys
    4. /
  4. SPA-1001
    5. /
  5. 31
Page 151 / 186 Scroll up to view Page 146 - 150
5-67
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5
Linksys ATA Field Reference
User 1/2 Tab
Speed Dial Settings
Supplementary Service Settings
The Linksys IP phone provides native support of a large set of enhanced or supplementary services. All
of these services are optional. The parameters listed in the following table are used to enable or disable
a specific supplementary service. A supplementary service should be disabled if a) the user has not
subscribed for it, or b) the Service Provider intends to support similar service using other means than
relying on the Linksys IP phone.
Field
Description
Speed Dial 2/3/4/5/6/7/8/9
Target phone number (or URL) assigned to speed dial 2, 3, 4, 5, 6, 7, 8, or 9.
The default is blank.
Field
Description
CW Setting
Call Waiting on/off for all calls.
The default is yes.
Block CID Setting
Block Caller ID on/off for all calls.
The default is no.
Block ANC Setting
Block Anonymous Calls on or off.
The default is no.
DND Setting
DND on or off.
The default is no.
CID Setting
Caller ID Generation on or off.
The default is yes.
CWCID Setting
Call Waiting Caller ID Generation on or off.
The default is yes.
Dist Ring Setting
Distinctive Ring on or off.
The default is yes.
Secure Call Setting
If yes, all outbound calls are secure calls by default.
The default is no.
Miss Call Shortcut
Enables or disables the display of missed calls on the LCD display.
Message Waiting
This is updated when there is voicemail notification received by the Linksys IP phone.
The user can also manually modify it to clear or set the flag. Setting this value to yes can
activate stutter tone and VMWI signal. This parameter is stored in long term memory and
will survive after reboot or power cycle.
The default is no.
Page 152 / 186
5-68
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5
Linksys ATA Field Reference
User 1/2 Tab
Distinctive Ring Settings
Caller number patterns are matched from Ring 1 to Ring 8. The first match (not the closest match) will
be used for alerting the subscriber.
Ring Settings
Accept Media Loopback
Request
Determines how the media loopback request is enabled. Choose automatic, never, or
manual.
The default is automatic.
Media Loopback Mode
Determines the media loopback mode. Choose source or mirror.
Media Loopback Type
Determines the media loopback type. Choose media or packet.
Field
Description
Field
Description
Ring1/2/3/4/5/6/7/8 Caller
Caller number pattern to play Distinctive Ring/CWT 1, 2, 3, 4, 5, 6, 7, or 8.
The default is blank.
Field
Description
Default Ring
Default ringing pattern, 1 – 8,
for all callers.
The default is 1.
Default CWT
Default CWT pattern, 1 – 8, for all callers.
The default is 2.
Hold Reminder Ring
Ring pattern for reminder of a holding call when the phone is on-hook.
The default is None.
Call Back Ring
Ring pattern for call back notification.
The default is None.
Cfwd Ring Splash Len
Duration of ring splash when a call is forwarded
(0 – 10.0s).
The default is 0.
Cblk Ring Splash Len
Duration of ring splash when a call is blocked (0 – 10.0s).
The default is 0.
Page 153 / 186
5-69
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5
Linksys ATA Field Reference
User 1/2 Tab
VMWI Ring Splash Len
Duration of ring splash when new messages arrive before the VMWI signal is applied (0
– 10.0s).
The default is .5.
VMWI Ring Policy
The parameter controls when a ring splash is played when a the VM server sends a SIP
NOTIFY message to the Linksys IP phone indicating the status of the subscriber’s mail
box. 3 settings are available:
New VM Available – ring as long as there is 1 or more unread voicemail
New VM Becomes Available – ring when the number of unread voicemail changes from
0 to non-zero
New VM Arrives – ring when the number of unread voicemail increases.
The default is New VM Available.
Ring On No New VM
If enabled, the Linksys IP phone will play a ring splash when the VM server sends
SIP
NOTIFY message to the Linksys IP phone indicating that there are no more unread
voicemails. Some equipment requires a short ring to precede the FSK signal to turn off
VMWI lamp.
The default is no.
Field
Description
Page 154 / 186
5-70
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5
Linksys ATA Field Reference
PSTN User Tab (SPA3102/AG310)
PSTN User Tab (SPA3102/AG310)
This section describes the fields for the following headings on the PSTN User tab on the SPA3102:
•
PSTN-To-VoIP Selective Call Forward Settings, page 5-70
•
PSTN-To-VoIP Speed Dial Settings, page 5-70
•
PSTN Ring Thru Line 1 Distinctive Ring Settings, page 5-70
•
PSTN Ring Thru Line 1 Ring Settings, page 5-71
•
PSTN/VoIP Caller Commands via DTMF, page 5-71
Note
References in this section to the SPA3102 also apply to the AG310.
PSTN-To-VoIP Selective Call Forward Settings
PSTN-To-VoIP Speed Dial Settings
PSTN Ring Thru Line 1 Distinctive Ring Settings
Field
Description
Cfwd Sel1 Caller
First of eight PSTN Caller Number Patterns to be blocked for VoIP gateway services or
forwarded to a certain VoIP number. If the caller is blocked, the SPA will not auto-answers
the call.
Cfwd Sel1 Dest
VoIP destination to forward a PSTN caller matching <Cfwd Sel1 Caller>. If this entry is
blank, the PSTN caller is blocked for VoIP service.
Block Last Caller
ID of caller blocked via the Block Last Caller service
Accept Last Caller
ID of caller accepted via the Accept Last Caller service
Field
Description
Speed Dial 2/3/4/5/6/7/8/9
The VoIP number to call when the PSTN caller dials a single digit ‘2’
Field
Description
Ring1/2/3/4/5/6/7/8 Caller
First of 8 PSTN Caller Number Patterns such that the corresponding ring will be used to
ring through Line 1 if the PSTN caller matches this pattern.
Page 155 / 186
5-71
Linksys IP Phone Administrator Guide
Document Version 3.2
Chapter 5
Linksys ATA Field Reference
PSTN User Tab (SPA3102/AG310)
PSTN Ring Thru Line 1 Ring Settings
PSTN/VoIP Caller Commands via DTMF
Field
Description
Default Ring
The default ring to be used to ring through Line 1. Choose from {1,2,3,4,5,6,7,8,Follow
Line 1}. If Follow Line 1 is selected, the ring to be used is determined by Line 1’s
distinctive ring settings.
The default is 1.
Field
Description
**#
Disconnect the PSTN line (SPA will take the FXO port on-hook).
**1
End the current call and restarts dial tone.

Rate

4 / 5 based on 1 vote.

Popular Linksys Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top