Linksys SPA-1001 Router Manual PDF (Setup & Configuration Guide)

Page 106 / 186 Scroll up to view Page 101 - 105

5-22

Linksys IP Phone Administrator Guide

Document Version 3.2

Chapter 5

Linksys ATA Field Reference

Regional Tab

Distinctive Ring/CWT Pattern Names

CWT6 Cadence

Cadence script for distinctive CWT 6.

The default is 30(.1/.1, .3/.1, .1/9.3).

CWT7 Cadence

Cadence script for distinctive CWT 7.

The default is 30(.1/.1, .3/.1, .1/9.3).

CWT8 Cadence

Cadence script for distinctive CWT 8.

The default is 2.3(..3/2).

Field

Description

Ring1 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 1 for the inbound

call.

The default is Bellcore-r1.

Ring2 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 2 for the inbound

call.

The default is Bellcore-r2

.

Ring3 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 3 for the inbound

call.

The default is Bellcore-r3

.

Ring4 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 4 for the inbound

call.

The default is Bellcore-r4

.

Ring5 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 5 for the inbound

call.

The default is Bellcore-r5

.

Ring6 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 6 for the inbound

call.

The default is Bellcore-r6

.

Ring7 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 7 for the inbound

call.

The default is Bellcore-r7

.

Ring8 Name

Name in an INVITE’s Alert-Info Header to pick distinctive ring/CWT 8 for the inbound

call.

The default is Bellcore-r8

.

Page 107 / 186

5-23

Linksys IP Phone Administrator Guide

Document Version 3.2

Chapter 5

Linksys ATA Field Reference

Regional Tab

Ring and Call Waiting Tone Spec

Control Timer Values (sec)

Field

Description

Ring Waveform

Waveform for the ringing signal.

The default is Sinusoid.

Ring Frequency

Frequency of the ringing signal. Valid values are 10–100 (Hz).

The default is 25.

Ring Voltage

Ringing voltage. 60–90 (V).

The default is 70.

CWT Frequency

Frequency script of the call waiting tone. All distinctive CWTs are based on this tone.

The default is 440@-10.

Field

Description

Hook Flash Timer Min

Minimum on-hook time before off-hook qualifies as hook-flash. Less than this the

on-hook event is ignored. Range: 0.1–0.4 seconds.

The default is 0.1.

Hook Flash Timer Max

Maximum on-hook time before off-hook qualifies as hook-flash. More than this the

on-hook event is treated as on-hook (no hook-flash event). Range: 0.4–1.6 seconds.

The default is 0.9.

Callee On Hook Delay

Phone must be on-hook for at this time in sec before the Linksys IP phone will tear down

the current inbound call. It does not apply to outbound calls. Range: 0–255 seconds.

The default is 0.

Reorder Delay

Delay after far end hangs up before reorder tone is played. 0 = plays immediately, inf =

never plays. Range: 0–255 seconds.

The default is 5.

Call Back Expires

Expiration time in seconds of a call back activation. Range: 0–65535 seconds.

The default is 1800.

Call Back Retry Intvl

Call back retry interval in seconds. Range: 0–255 seconds.

The default is 30.

Call Back Delay

Delay after receiving the first SIP 18x response before declaring the remote end is

ringing. If a busy response is received during this time, the Linksys IP phone still

considers the call as failed and keeps on retrying.

The default is 0.5.

Page 108 / 186

5-24

Linksys IP Phone Administrator Guide

Document Version 3.2

Chapter 5

Linksys ATA Field Reference

Regional Tab

Vertical Service Activation Codes

Vertical Service Activation Codes are automatically appended to the dial-plan. There is

no

need to include them in dial-plan, although

no

harm is done if they are included.

VMWI Refresh Intvl

Interval between VMWI refresh to the CPE.

The default is 0.5.

Interdigit Long Timer

Long timeout between entering digits when dialing. The interdigit timer values are used

as defaults when dialing. The Interdigit_Long_Timer is used after any one digit, if all

valid matching sequences in the dial plan are incomplete as dialed. Range: 0–64 seconds.

The default is 10.

Interdigit Short Timer

Short timeout between entering digits when dialing. The Interdigit_Short_Timer is used

after any one digit, if at least one matching sequence is complete as dialed, but more

dialed digits would match other as yet incomplete sequences. Range: 0–64 seconds.

The default is 3.

CPC Delay

Delay in seconds after caller hangs up when the Linksys IP phone starts removing the

tip-and-ring voltage to the attached equipment of the called party. Range: 0–255 seconds.

Linksys IP phone has had polarity reversal feature since release 1.0 which can be applied

to both the caller and the callee end. This feature is generally used for answer supervision

on the caller side to signal to the attached equipment when the call has been connected

(remote end has answered) or disconnected (remote end has hung up). This feature should

be disabled for the called party (in other words, by using the same polarity for connected

and idle state) and the CPC feature should be used instead.

Without CPC enabled, reorder tone will is played after a configurable delay.

If CPC is enabled, dial tone will be played when tip-to-ring voltage is restored

Resolution is 1 second.

The default is 2.

CPC Duration

Duration in seconds for which the tip-to-ring voltage is removed after the caller hangs up.

After that, tip-to-ring voltage is restored and dial tone applies if the attached equipment

is still off-hook. CPC is disabled if this value is set to 0. Range: 0 to 1.000 second.

Resolution is 0.001 second.

The default is 0 (CPC disabled).

Field

Description

Call Return Code

This code calls the last caller.

The default is *69.

Call Redial Code

Redials the last number called. (Not in PAP2T)

The default is *07.

Blind Transfer Code

Begins a blind transfer of the current call to the extension specified after the activation

code.

The default is *98.

Page 109 / 186

5-25

Linksys IP Phone Administrator Guide

Document Version 3.2

Chapter 5

Linksys ATA Field Reference

Regional Tab

Call Back Act Code

Starts a callback when the last outbound call is not busy.

The default is *66.

Call Back Deact Code

Cancels a callback.

The default is *86.

Call Back Busy Act Code

Starts a callback when the last outbound call is busy. (Not in PAP2T)

The default is *05

Cfwd All Act Code

Forwards all calls to the extension specified after the activation code.

The default is *72.

Cfwd All Deact Code

Cancels call forwarding of all calls.

The default is *73.

Cfwd Busy Act Code

Forwards busy calls to the extension specified after the activation code.

The default is *90.

Cfwd Busy Deact Code

Cancels call forwarding of busy calls.

The default is *91.

Cfwd No Ans Act Code

Forwards no-answer calls to the extension specified after the activation code.

The default is *92.

Cfwd No Ans Deact Code

Cancels call forwarding of no-answer calls.

The default is *93.

Cfwd Last Act Code

Forwards the last inbound or outbound calls to the extension specified after the activation

code.

The default is *63.

Cfwd Last Deact Code

Cancels call forwarding of the last inbound or outbound calls.

The default is *83.

Block Last Act Code

Blocks the last inbound call.

The default is *60.

Block Last Deact Code

Cancels blocking of the last inbound call.

The default is *80.

Accept Last Act Code

Accepts the last outbound call. It lets the call ring through when do not disturb or call

forwarding of all calls are enabled.

The default is *64.

Accept Last Deact Code

Cancels the code to accept the last outbound call.

The default is *84.

CW Act Code

Enables call waiting on all calls.

The default is *56.

Page 110 / 186

5-26

Linksys IP Phone Administrator Guide

Document Version 3.2

Chapter 5

Linksys ATA Field Reference

Regional Tab

CW Deact Code

Disables call waiting on all calls.

The default is *57.

CW Per Call Act Code

Enables call waiting for the next call.

The default is *71.

CW Per Call Deact Code

Disables call waiting for the next call.

The default is *70.

Block CID Act Code

Blocks caller ID on all outbound calls.

The default is *67.

Block CID Deact Code

Removes caller ID blocking on all outbound calls.

The default is *68.

Block CID Per Call Act Code

Blocks caller ID on the next outbound call.

The default is *81.

Block CID Per Call Deact Code

Removes caller ID blocking on the next inbound call.

The default is *82.

Block ANC Act Code

Blocks all anonymous calls.

The default is *77.

Block ANC Deact Code

Removes blocking of all anonymous calls.

The default is *87.

DND Act Code

Enables the do not disturb feature.

The default is *78.

DND Deact Code

Disables the do not disturb feature.

The default is *79.

CID Act Code

Enables caller ID generation.

The default is *65.

CID Deact Code

Disables caller ID generation.

The default is *85.

CWCID Act Code

Enables call waiting, caller ID generation.

The default is *25.

CWCID Deact Code

Disables call waiting, caller ID generation.

The default is *45.

Dist Ring Act Code

Enables the distinctive ringing feature.

The default is *26

Dist Ring Deact Code

Disables the distinctive ringing feature.

The default is *46.

Rate

Popular Linksys Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share