Page 16 / 43
Scroll up to view Page 11 - 15
C. User Guide
10
System
±
“
Administration Password
”
±
“
Remote Access
”
Status
±
Internet Connection
±
Wireless Connection
±
Traffic Statistics
±
DHCP Table
±
ARP Table
4.1
Overview
The Overview page displays useful current information about Sinope568+. The page shows the network
addresses being used by Sinope568+ to connect to your PCs, and for your Internet connection, as well as
the version information for Sinope568+.The hardware version information is set by Iskratel so the make
and model of your device can be quickly identified in the unlikely even that you need assistance.
Figure 4-1: Device Overview
4.2
Save Configuration
This page allows you to save the current configuration changes you have made to the flash memory of the
device.
1.
Select
Configuration
>
Save Configuration
. The following page opens.
Page 17 / 43
4.3 Internet
11
Figure 4-2: Save Configuration page
2.
To save the changes you have made, click
Commit
.
4.3
Internet
You can access the Internet in one of several ways depending on the service provided by your Internet
Service Provider (ISP):
±
Automatically detect settings. With this access type, Sinope568+ will scan for a link to the Internet.
±
Using PPPoA (Point to Point Protocol over ATM) allows Internet access only after you have entered a
valid username and password.
±
Using PPPoE (Point to Point Protocol over Ethernet) allows Internet access only after you have
entered a valid username and password.
±
Using DHCP (Dynamic Host Control Protocol) automatically allows Internet access.
±
Use direct manual settings provided to you by your ISP.
4.3.1
To establish internet connection
1.
Select
Configuration
>
Internet
. The following page opens.
Note: Some providers do not support all connection types listed above. In this case only
available types are displayed!
i
Page 18 / 43
C. User Guide
12
Figure 4-3: Internet connection configuration page
2.
Click
Connect
. The
Log In
page opens.
Figure 4-4: Log In page
3.
Type the username and password provided by your ISP. To continue, click
Connect
.
4.4
Local Network Configuration
These pages allow you to configure the following settings:
±
“
IP Address
”
±
“
UPnP
”
±
“
Global DHPC Settings
”
±
“
DHPC Server Configuration
”
To access these settings:
1.
Select Configuration >
Local Network
. The
Local Network Configuration
page opens.
Page 19 / 43
4.4.1 IP Address
13
Figure 4-5: Local Network Configuration page
2.
The settings are accessible through tabs listed below the page title. To access a specific setting, click
the corresponding tab.
4.4.1
IP Address
The IP address page displays the IP address and subnet mask for Sinope568+. These provide a unique
address for Sinope568+, as well as giving it the range of addresses to use for other PCs that are
connected to Sinope568+. Sinope568+'s default IP address and subnet mask are suitable for most
networks.
1.
In the
Local Network Configuration
page, click the
IP Address
tab. The following page opens.
Figure 4-6: IP Address page
2.
If you change any of the settings, confirm and save the settings by clicking
Apply
.
Page 20 / 43
C. User Guide
14
4.4.2
UPnP
Universal Plug and Play (UPnP) is an architecture for pervasive peer-to-peer network connectivity of
intelligent appliances, wireless devices, and PCs of all form factors. It is designed to bring easy-to-use,
flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a small
business, public spaces, or attached to the Internet. Universal Plug and Play is a distributed, open
networking architecture that leverages TCP/IP and the Web technologies to enable seamless proximity
networking in addition to control and data transfer among networked devices in the home, office, and
public spaces.
1.
In the
Local Network Configuration
page, click the
UPnP
tab. The following page opens.
Figure 4-7: UPnP Settings
2.
Click
Enable UPnP
to help support applications that would not otherwise work behind a Router.
3.
To continue, click
Apply
.
4.4.3
Global DHPC Settings
The
Global DHCP Settings
page allows you to enable or disable DHCP Server running on your
Sinope568+. DHCP Server can automatically configure your PCs connected to Sinope568+ to be able to
connect to the Internet. You must enable DHCP Client (Automatically configure IP address) on your
computer.
1.
In the
Local Network Configuration
page, click the
Global DHCP Settings
tab. The following page
opens.
19216811.live