Page 11 / 43
Scroll up to view Page 6 - 10
3.2 Light indicators
5
Table 3-1:
Light indicators
LED
Status
Description
Power
off
Power is off.
on (30%)
Power is on but there is no device activity.
on (70%)
Broadband line is established.
blinking slow
The device is trying to detect the broadband carrier signal.
blinking fast
The broadband carrier is detected and the device is trying to train.
Broadband
off
No IP connection.
on (70%)
IP session is established, no WAN traffic.
flickering
IP session is established, WAN traffic activity.
blinking slow
IP connection failed.
Data
off
No devices connected to the home gateway, or the devices are
turned off.
on (70%)
Devices are connected to the home gateway and turned on.
flickering
Data transfer activity.
Wireless
off
Wireless access point is disabled.
on (70%)
Wireless access point is enabled.
flickering
Wireless connection is in use.
Phone
off
Phone service is disabled.
on (70%)
Phone service is enabled.
blinking
Phone service is in use.
Page 12 / 43
C. User Guide
6
3.3
Support leg
Insert the modem into the support leg provided (see figure below), then place the unit on a flat even
surface.
Figure 3-3: Support leg installation
3.4
Preliminary setup
3.4.1
LAN and TCP/IP setup
This section of the manual provides important information to keep in mind when setting up the first
connection between your computer and Sinope568+ home gateway.
The factory default settings of the Sinope568+ home gateway have values listed bellow:
3.4.2
User defined IP address
The default option is to set up the connection by yourself. In this case you must specify the IP address of
your system. Be careful that the subnet values of your system and the modem are the same, e.g.
192.168.1.0 (IP address 192.168.
1
.1 for modem and IP address 192.168.
1
.2 for computer). Example is
shown on the picture bellow.
Table 3-2:
Factory default settings
Local IP address
192.168.1.1
Subnet mask
255.255.255.0
DHCP server
Disabled
Page 13 / 43
3.4.3 Obtain an IP automatically
7
Figure 3-4: User defined IP address set up for Local Area Connection on computer
The IP address of the modem can also be changed, you can learn about that under the WEB management
connection sections of the manual.
3.4.3
Obtain an IP automatically
If you enable DHCP server in Sinope568+, is the easiest way to set up a connection to configure the LAN
adapter on your system to obtain an IP automatically. This can be done in your operational system by
managing the Local Area Connection Properties. The TCP/IP protocol must be installed on your system
and set to obtain an IP address automatically. Example is shown on the picture below.
Page 14 / 43
C. User Guide
8
Figure 3-5: IP obtain automatically set up for Local Area Connection on computer
3.5
WEB management connection
Sinope568+ home gateway has embedded WEB server included in the firmware. This section of the
document describes the basic principles on how to manage the settings of the Sinope568+ home gateway
using WEB management connection with any web browser.
1.
To access Web management connection enter the URL in your web browser http://<ipaddress>, for
example
.
<ipaddress> is the Local IP address of the Sinope568+ home gateway, e.g.
192.168.1.1 for factory
default settings. The IP addresses of modem and computer must be parts of the same IP network (e.g.
192.168.1.0).
The following dialog box opens.
Figure 3-6: Web connection
2.
Enter the user name
user
and password
user
.
Page 15 / 43
3.5.1 About the Web management
9
3.
Click
OK
to continue. The following page opens.
Figure 3-7: Overview page
3.5.1
About the Web management
The Web management interface enables you to view your modem settings, edit and configure them.
The interface is divided into two frames:
±
left frame - navigation tree
The navigation tree is intended for navigating and accessing the modem configuration pages.
The elements listed in the tree are hyperlinks. When you click a link, a corresponding configuration
page will be displayed in the right frame.
±
right frame - display area
Displays a configuration page for the selected element.
4
Managing Sinope568+ Router
This section describes the web management interface, configuration options and gives instructions for
configuring your router.
The main areas of configuration are divided into the following groups and elements:
Device
±
“
Overview
”
Configuration
±
“
Save Configuration
”
±
“
Internet
”
±
“
Local Network Configuration
”
±
“
Wireless Network
”
±
“
Voice Configuration
”
±
“
Security
”
±
“
DNS settings
”
±
“
Port Configuration
”
19216811.live