Page 26 / 63
Scroll up to view Page 21 - 25
2
Double-click on “Network
Connection”.
3
Go to Local Area Connection
Properties.
4
Scroll down, select the
“Internet
protocol (TCP/IP)”. If
there is no TCP/IP line listed, you
will need to install TCP/IP first by
pressing “Install…” button.
5
Press the “Properties” button.
25
Page 27 / 63
6
Check “Obtain an IP address
automatically”.
7
Check “Obtain DNS Server
address automatically”.
8
Click OK to exit Properties
9
If asked to re-start the PC, click
“YES”.
Configuring Ethernet Connection
Your EV-DO Modem provides an embedded Web-based Management Utility to
help you configure it using your Web Browser. Follow these steps to configure
your Modem’s Ethernet connection.
1. Open your Web browser and enter
192.168.0.1 in the address bar
26
Page 28 / 63
2. A pop-up window will appear. When
prompt for User name and password,
enter the following user id and
password.
User Name:
admin
Password:
admin
* If you have changed the user name
and the password, enter the new user
name and password.
Note
: This user name and password
are only for the Web Manager access.
Changing these settings does not
change AxessManager user profile name and password.
After entering the correct user name and password, the pop up window will
change to a web-based window.
Follow the steps in the chapter “Web Manager User Interface”, “Step 2 Navigate
web-based UI”, page 39 to complete the Modem’s Ethernet and Wi-Fi settings.
27
Page 29 / 63
AxessManager Operational Guide
AxessManager is a Software utility that allows the administration of your Modem.
One computer at a time can log into the Modem via AxessManager for the
purposes of making changes to the settings of the Modem. Once a user has
logged in to make changes, all other computers connected to the Modem inherit
the same settings. For example, if the Modem is set to use only 1X packet data,
all connections to the network through the Modem RJ-45 ports or Wi-Fi will be
1X.
Using the Main Window User Interface
The Main window is the first page you will see when you access the
AxessManager User Interface (UI). The Main window shows you a quick view of
the Modem’s status and settings. All advanced setup pages can be reached from
this page.
28
1. Signal Strength Icon
This icon indicates the signal strength of the EV-DO network serving your
Modem. The range below applied to EV-DO signal only.
OFF
No Modem connected to computer
Antenna only- Red
Modem connected but no service
Antenna only-White
Weak signal (< -111 dBm)
Antenna + 1 bar
Low signal (-111
≤
sig. < -103 dBm )
Antenna + 2 bars
Medium-Low (-103
≤
sig. < -98 dBm)
Antenna + 3 bars
Medium signal (-98
≤
sig. < -93 dBm)
Antenna + 4 bars
Medium-high (93
≤
sig. < -88 dBm)
Antenna + 5 bars
Strongest signal (
≥
-88 dBm)
[3]
[4]
Page 30 / 63
29
2. Battery Icon
OFF
No battery
Blinking red
Battery error or very low
Blue empty battery
Battery low level
Blue with 1 bar
Battery level 25%
Blue with 2 bars
Battery level 50%
Blue with 3 bars
Battery level 75%
Blue with 4 bars
Battery level close to 100%
Progressing 1- 4 bars
Battery is charging
3. Network Connection Icon
This icon shows the wired network connection mode of your Modem. Only one
mode can be used at a time.
OFF
No computers connected to Modem
Ethernet
RJ-45 port or Wi-Fi is in use
USB
USB port is in use
COM
COM port is in use
Note that there is a USB/Ethernet switch in the front of the Modem to select
which preferred mode for your connected computers. The COM mode can only
be activated from the "Menu" window.
4. Air Interface Icon
This icon informs you that the Modem is tuned to a 1x or EV-DO wireless
network. By default your Modem is programmed to search and use EV-DO
network. If unavailable, the Modem will try to search for a 1x network.
OFF
No network available, no service
EV-DO
EV-DO network is available
1xRTT
1X network is available
5. Activity Icon
This icon indicates data activity between your Modem and the network.
OFF
No data activity
Blinking arrows
Data passing through your Modem
Steady arrows
Modem is in connect or dormant state
19216811.live