Page 16 / 63 Scroll up to view Page 11 - 15
15
Connecting and Configuring your Modem
Each Modem has been provisioned at the factory for use with a particular service
provider. This sets the Modem to use particular radio channels and enables
services specific for that provider.
Although the Modem comes with drivers and enabling software, you don’t have
to install and use them if you simply want to connect to the Internet through the
Ethernet (RJ-45) ports
, assuming that your Modem has been activated with the
network. Simply connect your computer with the Modem using the provided
Ethernet (RJ-45) cable and you are ready to use the Internet.
However, if you want to connect to the Internet through USB port
, you must
install AxessManager software.
If you choose to install the drivers and its enabling software (the AxessManager),
you will have more controls of the Modem performances and settings. You will
also have access to more advance features of the Modem such as Wi-Fi
configuration (D-35 series only), USB connection and password management.
This chapter provides the step-by-step process to install the AxessManager
connectivity software.
Install Software
ice.net has provided our Install software to make installing your Modem a simple
and easy task. You can use it to get your Modem up and running in minutes.
The Install software requires that your Windows Me, 2000, or XP computer be
connected directly to your Modem.
IMPORTANT
: Run the Install software from the computer that is going to be the
main connection with the Modem.
DO NOT CONNECT THE MODEM AT THIS TIME.
Step 1
Run the Install Software
1.1.
Shut down any programs that are running on your computer at this time.
1.2
Make sure you have the following items at the computer that is going to be
the main connection with the Modem. DO NOT CONNECT THE MODEM
AT THIS TIME.
Page 17 / 63
16
Quick Installation Guide
The Install Software CD with User Manual
The Modem
The Modem’s Power Supply
RJ-45 Ethernet Networking Cable
1.3
Turn off any firewall or Internet-connection-sharing software on your
computer.
1.4
Insert the Install software CD into your CD-ROM drive. The Installation
screen will automatically appear on your screen within 15 seconds. If it
does not, select your CD-ROM drive from “My Computer” and double-click
on the file named “EasyInstall.exe” on the CD-ROM.
Step 2
Set up the Hardware
2.1.
Make sure your Modem is not connected to any power source and all the
LED are OFF.
2.2
Locate the RJ-45 Ethernet cable that is included with your Modem. Plug
one end of this cable into ANY one of the Ethernet ports on your Modem.
Plug the other
end of the cable into the networking port on your computer.
2.3
Locate the power supply that is included with your Modem. Plug the power
supply’s small connector into the power port on the Modem. Plug the
power supply into an empty power outlet.
2.4
Switch on the Modem. Look at the Power LED on top of the Modem and
make sure the lights are ON.
2.5
Wait for a few seconds for the Modem to search for service network. Once
the Modem finds a suitable network, observe the Signal LED turns to Red,
Orange or Green depending on the strength of acquired signal. Refer to
the Signal Strength LED description for more details.
Step 3
Preparing your PC
Your Modem’s Ethernet is configured with DHCP by default. This means that IP
address of your PC is automatically assigned by the Modem. Make sure that
your PC has the correct TCP/IP setting for its "Local Area Connection" by
following the steps below.
Page 18 / 63
3.1 Click "Start", select "Connect
To"
and scroll down to "Show all
connections" and left click it.
3.2 Right click "Local Area
Connection" scroll down to
"Properties" and left click it
3.3 Scroll down, select the “Internet
Protocol (TCP/IP)”. Press the
“Properties” button.
If there is no TCP/IP line listed, you
will need to install TCP/IP first by
pressing “Install…” button.
17
Page 19 / 63
3.4 Check “Obtain an IP address
automatically”
3.5 Check “Obtain DNS Server
address automatically”
3.6 Click Ok to exit Properties
3.7 If asked to re-start the PC, click
“YES”.
18
Page 20 / 63
Using USB with your Modem
The Modem has one USB Type B port to provide connectivity for computers
equipped with USB. If you choose to use the USB with your Modem, you first
need to install the provided USB device driver into your computer.
This chapter provides the step-by-step process to install the USB device driver.
IMPORTANT
: Run the USB device driver installation from the computer that is
going to be the main connection with the Modem.
DO NOT CONNECT THE MODEM AT THIS TIME.
Step 1
Run the Setup Software
1.1.
Shut down any programs that are running on your computer at this time.
1.2
Make sure you have the following items at the computer that is going to be
the main connection with the Modem. DO NOT CONNECT THE MODEM
AT THIS TIME.
Quick Installation Guide
The Install Software CD with User Manual
The Modem
The Modem’s Power Supply
USB Cable
1.3
Insert the Install software CD into your CD-ROM drive. Locate the folder
“Driver”. You will see two subfolders: “Install 32” and “Install 64”. For PC
with
Windows Vista 64
, use “Install 64”. Otherwise, use “Install 32”.
1.4
Press “MSP_Install.exe”. The following screen will appear. Select “Install”.
19

Rate

4.5 / 5 based on 2 votes.

Popular ice.net Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top