Huawei HG622 Router Manual PDF (Setup & Configuration Guide)

Page 11 / 29 Scroll up to view Page 6 - 10

2.3

Connecting Multiple Telephones

If your telephone line is used for the broadband network access, telephone connections,

and fax connections, take the following figure as a reference for connecting the cables.

1

4

5

PHONE

MODEM

LINE

2

3

DSL

LAN4

LAN3

LAN2

LAN1

RESET

POWER

1

6

7

8

3

1. Telephone jack

on the wall

2. Splitter

3. Telephone

4. Computer

5. Power adapter

6. T connector

7. Microfilter

8. Fax machine

6

Page 12 / 29

2.4

Powering On

To power on the HG622, press the ON/OFF button on the side panel of the HG622.

After you power on the HG622, the DSL indicator blinks (for less than three minutes),

which indicates that the HG622 is being activated. Later, the DSL indicator turns solid

on. The POWER indicator is also solid on, which indicates that the HG622 is working

properly.

3

Setting the Internet Access Parameters

The HG622 supports VDSL2 uplink and High-Speed Packet Access (HSPA) uplink

through Huawei HSPA data card. Realizes dynamic mutual backup of voice and data

services through the DSL link and HSPA link.

3.1

Configuring the HSPA uplink

When the HG622 is working through the Huawei HSPA data card, you need to install

the Huawei HSPA data card on the HG622 so that your PC can connect to the Internet

through HSPA uplink. To create a HSPA uplink connection, do as follows:

Step 1

Log in to the Web-based configuration utility.

1.

Launch the Internet Explorer on your computer. Enter

http://192.168.1.1

in the address bar, and then press

Enter

.

2.

In the displayed dialog box, enter the user name and the password, and

then click

Login

.

By default, both the user name and the password are

admin

. After the user name and

the password are verified, you can access the Web-based configuration utility.

Step 2

Click

Basic

>

WAN

in the navigation tree to display the

WAN Connection

Page.

Step 3

Click the connection whose access type is UMTS.

Step 4

Select

Enable

for

WAN connection

.

Step 5

Enter the APN and the Dial number that are provided by the network operator

in the

APN

text box and the

Dial number

text box.

Step 6

Enter the user name and password in the

User name

and

Password

text

boxes that you can configure.

Step 7

Click the

Submit

button to finish the UMTS settings.

If you want to verify the PIN code of your SIM card, then do as follows:

7

Page 13 / 29

Step 1

Click

Advanced

>

in the navigation tree to display the

Page.

Step 2

Enter the original PIN number in the

text box.

Step 3

Click the

Submit

button to finish the settings on the

Page.

Use the default values for the other parameters. In general, they do not need

to be configured.

3.2

Configuring the DSL uplink

By configuring the HG622 and your computer, you can choose any of the following

methods to surf the Internet:

z

Using the Embedded PPP Dial-Up Software on the HG622

z

Using the PPP Dial-Up Software on Your Computer

Using the Embedded PPP Dial-Up Software on the HG622

If you select this method for accessing the network, the HG622 starts to set up a dial-up

connection automatically after the startup. You can access the network after you power

on your computer. You do not need to install any special dial-up software on your

computer or perform dial-up operations on your computer. To configure the HG622 and

your computer for the network access, do as follows:

Step 1

Log in to the Web-based configuration utility of the HG622.

Step 2

Configure the ATM PVC.

1.

In the navigation tree, choose

Basic

>

ATM

.

2.

Enter

VPI/VCI

provided by the Internet Service Provider (ISP).

3.

Select

EoA

from the

DSL link type

option button.

4.

Click

Submit

.

Step 3

Set WAN parameters.

1.

In the navigation tree, choose

Basic

>

WAN

.

2.

Select a PVC from the

Layer2 interface

drop-down combo box.

z

The name of this PVC should begin with

atm

.

z

The DSL link type of this ATM PVC should be

EoA

.

3.

Select

Enable

for WAN connection.

4.

Select a service from the

Service list

drop-down list box.

5.

Select a LAN interface from the

Port binding

check box.

6.

Select

Route

from the

Connection mode

drop-down list box.

7.

Select

PPPoE

from the

Connection type

option button.

8.

Enter the

User name

and

Password

provided by the ISP.

9.

Click

Submit

.

8

Page 14 / 29

Step 4

Set LAN parameters.

1.

In the navigation tree, choose

Basic

>

LAN

.

2.

Set the

IP address

and

Subnet mask

of the LAN connection.

3.

Select

Enable

for

DHCP serve

r, and then set the corresponding

parameters.

4.

Click

Submit

.

After you complete the preceding settings, you can surf the Internet.

You need to perform the preceding operations on a computer once only. The next time

when you power on your computer, you can surf the Internet without any configuration.

Using the PPP Dial-Up Software on Your Computer

If you select this method for accessing the network, you need to install and configure

the dial-up software on your computer. In addition, you need to perform dial-up

operations on your computer upon each startup. To configure the HG622 and your

computer for the network access, do as follows:

Step 1

Set the working mode of the HG622 to

Bridge

.

For details, refer to the procedure for enabling the embedded dial-up function described

in Step 3 in section "Using the Embedded PPP Dial-Up Software on the HG622." Note

that

Bridge

is selected from the

Connection mode

drop-down list box.

Step 2

Install and configure the PPP dial-up software on your computer.

The PPP dial-up software is pre-installed on certain computer operating systems. To

create a dial-up connection, do as follows (taking the Windows XP operating system as

an example):

1.

Choose

Start

>

All Programs

>

Accessories

>

Communications

>

Network Connections

.

2.

Click

Create a new connection

in

Network Tasks

to display the

New

Connection Wizard

window, and then click

3.

Select

Connect to the Internet

, and then click

4.

Select

Set up my connection manually

, and then click

5.

Select

Connect using a broadband connection that requires a user

name and password

, and then click

6.

Enter the name (as desired) of the dial-up connection in

ISP Name

, and

then click

7.

Select

Anyone's use

or

My use only

, and then click

8.

Enter the user name and password provided by the network operator and

used for the dial-up connection, and then click

9.

Select

Add a shortcut to this connection to my desktop

, and then click

Finish

.

An icon for the dial-up connection is displayed on the desktop of your computer.

9

Page 15 / 29

You need to perform the preceding operations only once for creating a network

connection. After the network connection is created, to access the network,

double-click the icon for the dial-up connection, and then click

Connect

in the

displayed dialog box.

4

Configuring

the

Wireless

Network

Connection

If a wireless network adapter is installed on your computer, you can connect you

computer to the HG622 through a wireless connection.

The hardware installation methods and driver installation methods of wireless

network adapters provided by different companies vary from each other. For

details, see the installation guide provided by the wireless network adapter

provider.

Setting Up a Wireless Connection Through the WPS Button

The HG622 supports the Wi-Fi Protected Setup (WPS) function. If your network

adapter also supports the WPS function, you can use the WPS function to set up a

wireless connection between your PC and the HG622 quickly. To set up a wireless

connection, do as follows:

Step 1

Enable the wireless network function, and set the wireless network name and

access password of the HG622, do as follows (taking the authentication type

WPA-PSK as an example):

1.

Log in to the Web-based configuration utility of the HG622.

2.

In the navigation tree on the left of the Web-based configuration utility,

choose

Basic

>

WLAN

.

3.

Select the

Enable

WLAN

option.

4.

Enter a wireless network name in the

SSID

text box.

5.

Select

WPA-PSK

from the

Security

drop-down combo box.

6.

Enter an access password in the

WPA pre-shared key

text box.

7.

Select

AES

from the

WPA encryption

drop-down combo box.

8.

Click

Submit

to save the settings.

Step 2

Press the WPS button of the HG622 to enable the HG622 to enter the WPS

negotiation state.

Step 3

Enable the WPS negotiation function of the wireless network adapter on your

PC within two minutes, and then wait for a moment (typically 10s and at most

120s).

10

Rate

Popular Huawei Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share